Hiniker DB1474A Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 47

Hiniker DB1474A Скачать руководство пользователя страница 20

TITLE

RIGHT WING WILL NOT STAY EXTENDED

Perform all initial inspections and checks listed on page 1 before beginning test procedure.

WARNING: Always retract wings fully, lower the plow to the ground and relieve pressure

before removing any fittings, hoses or caps. Allow the system to cool down before drain

-

ing oil or handling system components. Serious burns can result from contact with hot
oil. FAILURE TO HEED CAN RESULT IN SERIOUS INJURY OR DEATH.

RIGHT WING WILL NOT STAY EXTENDED

ALL OTHER FUNCTIONS ARE NORMAL.

Remove, inspect and clean Check Valve 3 (CV3).

See page 15.

Repair or replace as necessary.

DOES RIGHT WING STAY EXTENDED?

Remove, inspect and clean
S6 Solenoid Valve. See page 20.
Repair or replace as necessary.

Does Right Wing Stay Extended?

Yes

No

Call Hiniker Service

Yes

No

End

Remove, inspect and clean Relief Valve
2 (RV2). See page 19. Repair or replace
as necessary. Reinstall and adjust.
See page 31.

Does Right Wing Stay Extended?

Yes

No

End

10 Right Wing Will Not Extend

«
...
18
19
20
21
22
...
»

Содержание DB1474A
















































Отзывы:

Нет отзывов