Hiniker DB1474A страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 47

background image

TITLE

Check Valve Removal, Cleaning and Replacement 15

CHECK VALVE REMOVAL, CLEANING &

REPLACEMENT (CV1, CV2, & CV3)

WARNING: Always retract wings fully,
lower the plow to the ground and re-
lieve pressure before removing any

fittings, hoses or caps. Allow the system to

cool  down  before  draining  oil  or  handling
system  components.  Serious  burns  can  re-
sult  from  contact  with  hot  oil.  FAILURE  TO
HEED CAN RESULT IN SERIOUS INJURY OR
DEATH.

DWG NO. 5727

Remove the check valve using a 7/8” hex sock-
et.

PHOTO NO. 9016A

Inspect the check valve O-rings for wear and
contamination. Replace O-rings if necessary.
(P/N 25010992).

Using  a  plastic,  aluminum  or  soft  brass  probe,
push  on  the  ball  in  the  end  of  the  check  valve.
It  should  move  freely,  then  return  to  the  closed
position. If the ball sticks open, closed or binds,

replace the check valve (P/N 25010746). Clean,

repair or replace as necessary. Inspect endhead
and/or valve block cavity with pencil magnet for
contamination. Flush cavity with clean hydraulic
oil. Reinstall check valve and torque to 10-15 Ft.
lbs.

«
...
23
24
25
26
27
...
»

Содержание DB1474A
















































Отзывы:

Нет отзывов

Похожие инструкции для DB1474A

Бренд: Omega Страницы: 44

Бренд: Radionics Страницы: 14

FieldPoint FP-AI-100

Бренд: National Instruments Страницы: 17

Бренд: Yudian Страницы: 10

Бренд: BUCKINGHAM MFG Страницы: 7

Бренд: F.F. Group Страницы: 36

Бренд: H&H Страницы: 44

Бренд: SPT Страницы: 32

Бренд: Sanela Страницы: 7

Бренд: Major Страницы: 44

Бренд: STAMOS Страницы: 17

Multilin DGT Series

Бренд: GE Страницы: 60

DBI-SALA FlexiGuard M100

Бренд: 3M Страницы: 76

Ricon TITANIUM S Series

Бренд: Wabtec Страницы: 76

LogiCORE IP v1.02a

Бренд: Xilinx Страницы: 57

Бренд: Hwayuan Electric Страницы: 31

Бренд: Avalon Страницы: 86

Бренд: morse Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды