Hiniker DB1474A страница 42 Скачать руководство пользователя | Manualshive

Страница: 42 / 47

background image

32 Relief Valve Testing and Adjustment

PHOTO NO. 4129

PHOTO NO. 4132

WARNING: Always retract wings fully,
lower the plow to the ground and re-

lieve pressure before removing any fit

-

tings, hoses or caps. FAILURE TO HEED CAN
RESULT IN SERIOUS INJURY OR DEATH.

Remove the hex cap from either RV1 or RV2 de-
pending on which pressure relief valve is being
adjusted.

The slotted screw underneath the cap is for ad-
justing the relief valve pressure setting. Turning
the screw clockwise increases the pressure and
turning the screw counterclockwise decreases

the pressure. Turn the screw in 1/4 turn incre

-

ments until the pressure gauge indicates 2700
PSI +/– 100.

NOTE:

If no increase in pressure is observed

after  turning  the  adjustment  screw  clockwise,
either  the  pump  is  weak  (see  “Hydraulic  Pump
Test,”  page  27),  the  valve  has  dirt  between  the
valve ball and seat, or the spring is weak or bro-
ken.  See  Removal,  Cleaning  and  Replacement
page 17 and/or 18.

Ensure the hex cap threads and O-ring are clean
and serviceable and re-install cap.

NOTE:

If the hex cap does not screw onto the

adjustment screw easily by finger, it is possible

that the adjustment screw is turning with the hex
cap and the pressure setting has changed.

See testing procedure to ensure the adjustment
setting has not changed.

«
...
40
41
42
43
44
...
»

Содержание DB1474A
















































Отзывы:

Нет отзывов

Похожие инструкции для DB1474A

Бренд: Garaventa Lift Страницы: 58

Бренд: National Instruments Страницы: 15

Бренд: National Instruments Страницы: 20

Бренд: National Instruments Страницы: 22

NI PXI-665 Series

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 30

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 34

Бренд: Equalizer Страницы: 26

Бренд: Firepower Страницы: 32

Trailblazer 251

Бренд: Miller Страницы: 48

USB-1408FS-Plus-OEM

Бренд: Measurement Computing Страницы: 26

Бренд: Tuxedo Страницы: 33

Бренд: Nedap Страницы: 24

Бренд: SEW-Eurodrive Страницы: 384

VIPER CUT 30Mk II

Бренд: Xcel-Arc Страницы: 24

Бренд: Baileigh Industrial Страницы: 48

Бренд: Affordable Wheelchair Lifts Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды