Hiniker DB1474A страница 24 Скачать руководство пользователя | Manualshive

Страница: 24 / 47

background image

TITLE

14 DC Motor Brush Removal and Replacement

DC MOTOR BRUSH REMOVAL AND REPLACEMENT

WARNING: Disconnect Vehicle Battery
prior to performing this procedure to
avoid electrical shock or burns.

1

2

PHOTO NO. 8996A

Disconnect the black wire of the battery power ca-
ble at location 2. Disconnect the red (or red striped)
wire of the battery power cable from the motor ter-
minal at location 1.

PHILLIPS HEAD SCREWS

MOTOR CAP

MOTOR

DWG NO. 3514

Remove the two Phillips head screws from the mo-
tor cap. Remove motor cap.

PHOTO NO. 3747

NOTE:

If your motor is equipped with two (2)

brushes with bare wires (Ground brushes) and
two (2) brushes with insulated wires (POS brush-
es), make sure that you note location of the two
types and replace them with like type brushes.

WARNING: Failure to replace Brushes
correctly will severely damage Motor

and may cause electrical fires. FAIL

-

URE TO HEED CAN RESULT IN SERIOUS IN-
JURY OR DEATH.

PHOTO NO. 3749

Remove screws from brush leads. Carefully pry
back the tension spring with a straight slot screw-
driver and remove brush. Replace brush if it is

1/4” or less in length. (P/N 25010337)

IMPORTANT: Brushes should be replaced as
a set. DO NOT replace one Brush only.

Clean the motor commutator with a spray electri-
cal contact cleaner before installing brushes.

To install new brushes reverse the procedure.

«
...
22
23
24
25
26
...
»

Содержание DB1474A
















































Отзывы:

Нет отзывов

Похожие инструкции для DB1474A

Бренд: Japan' Gold Страницы: 5

RIS 700PE EKO 3.0

Бренд: Salda Страницы: 36

Бренд: WEST Страницы: 2

Бренд: T.L. FAHRINGER Страницы: 26

Бренд: EAE Страницы: 50

Бренд: Dhollandia Страницы: 69

KPN235WEK-WELIK-DC

Бренд: Ravaglioli Страницы: 76

Бренд: HURNER Страницы: 57

SITALI CXVM 280

Бренд: Olimpia splendid Страницы: 32

Бренд: CAME Страницы: 40

Бренд: Lutron Electronics Страницы: 36

Бренд: Lincoln Electric Страницы: 35

Smootharc Elite MIG 451 Progress Pulse

Бренд: BOC Страницы: 41

I/O SYSTEM 750 750-421

Бренд: WAGO Страницы: 12

Бренд: NCR Страницы: 14

Бренд: RF SOLUTIONS Страницы: 8

Бренд: Chamberlain Страницы: 92

CD3000S-1PH series

Бренд: CD Automation Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды