HIKVISION DS-7204HTI-K1 Скачать руководство пользователя страница 170

Страница: 170 / 188

DS-720xHTI-Kx DVR User Manual

169

14.6 Upgrading Camera

Purpose

You can upgrade multiple connected analog cameras supporting TurboHD or AHD signal simultaneously
with the DVR.

Go to

Menu > Maintenance > Upgrade > Camera Upgrade

Figure 14-9

Camera Upgrade

Check the checkbox(es) of the analog camera(s) to upgrade.

The analog camera(s) must support TurboHD or AHD signal.

Select the update file from the backup device.

Click

Upgrade

to start upgrading.

14.7 Restoring Default Settings

Go to

Menu > Maintenance > Default

Figure 14-10

Restore Defaults

Select the restore type from the following three options.

Содержание DS-7204HTI-K1





























































































































































































Результаты поиска

Содержание DS-7204HTI-K1

Отзывы:

Похожие инструкции для DS-7204HTI-K1

Бренды по названию

Популярные бренды

HIKVISION DS-7204HTI-K1, Руководство пользователя

Результаты поиска

Содержание DS-7204HTI-K1

Отзывы:

Похожие инструкции для DS-7204HTI-K1

Бренды по названию

Популярные бренды