HIKVISION DS-7204HTI-K1 Скачать руководство пользователя страница 147

Страница: 147 / 188

DS-720xHTI-Kx DVR User Manual

UM DS-720xHTI-Kx 012918NA

146

After exporting is complete, click

to finish the packet export.

Figure 11-22

Packet Export Attention

Up to 1 MB of data can be exported each time.

11.3.3 Checking Network Status

Purpose

You can check the network status and set the network parameters in this interface.

Go to

Menu > Maintenance > Network Detect > Network Detection

Click

Status

on the right bottom of the interface.

Figure 11-23

Checking Network Status

If the network is normal, the following message box pops out.

Figure 11-24

Network Status Checking Result

If the message box appears with other information, click

Network

to show the network parameters

quick setting interface.

Содержание DS-7204HTI-K1





























































































































































































Результаты поиска

Содержание DS-7204HTI-K1

Отзывы:

HIKVISION DS-7204HTI-K1, Руководство пользователя, Страница: 147 / 188

Результаты поиска

Содержание DS-7204HTI-K1

Отзывы: