manualshive.com logo in svg

HEIDELBERG MLA150, Руководство пользователя

Поделиться
Скачать
HEIDELBERG MLA150 Скачать руководство пользователя страница 22

MLA150 

 

3 System Description 
 

 
 

16 

User Guide

 

the required process temperature. The temperature control unit is located within the 
top compartment and has a display readout accessible from the outside through a 
hole in the flow box cover. In case the temperature e65°C inside the flow 
box, which can be caused by a malfunction of the fan, the control unit shuts down 
the heating system. The push button switch turns red. The heating system can be 
reset by pushing the button once but this should only be done if the reason for the 
failure is known. The display readout has a small icon in the left, blinking in regular 
intervals. This icon shows the activity of the heat output regulator. If the icon blinks 
periodically then the heat regulation works properly. If the icon is illuminated or not 
illuminated without any periodical change, then the temperature control unit is not 
working trouble-free anymore. It is recommended to shut down the system and call 
one of Heidelberg Instruments service offices (see 

1.2 Contact

). 

CASTOR WHEELS 

The flow box stands on eight castor wheels that have locking brakes in order to 
provide a stable position. These castor wheels are not height-adjustable. The 
machine is leveled by adjusting the four feet.  

SWITCH PANEL 

At the front side of the flow box several buttons are 
located. The green button is used for powering up the 
system, the red one is for powering it down. The 
button in the middle is the emergency off button. For 
opening and closing the window, the push button is 
used. The flow box provides a light source for inside, 
which is, depending on the application, yellow or red 
light. The light switch is located between the 
emergency off button and the window push button. 

 

 

WINDOW 

The window is opened only for loading and unloading purposes. During operation, 
the window cannot be opened for safety reasons. The push button at the front of the 
flow box opens and closes the window by means of compressed air. This button is 
disabled while an exposure is running. 

 

 

 

On (

I

) 

Off (

0

) 

Emergency Off

 

Window push button 

Light push button 

Содержание MLA150


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды