Harman PC45 Скачать руководство пользователя страница 4

Страница: 4 / 42

PC 45 Corn/Pellet Stove

Assembly and Installation

Fig. 1

Rear Cover

Panels

Shipping Bolts: These holes

are also used for Mobile Home

Installation

unpacking

The PC 45 is bolted to the skid to prevent movement

during shipping.

To free the stove from the skid you must remove the

hold-down bolts in the rear of the pedestal base.

Follow these instructions along with all local codes

regarding installation of this appliance.

NOT

use makeshift compromises when installing

this appliance, serious consequences may result.

With any hearth appliance, installation of smoke

detectors is recommended on every level of the home.

Possible causes of smoke detector activation:

Paint curing process - Open a window near the

appliance for the first few hours of burning.
Exhaust being drawn back inside the dwelling - Outside

air connection to the appliance is necessary.
Vent leakage - All interior seams and joints should be

sealed with silicone where appliacable. Follow vent

manufacturers instructions for proper sealing.

Firebrick

Install the firebrick vertically on the angle above the

burnpot.

removing or Installing rear panels

To remove the rear cover panels, loosen the screws

slightly and slide the covers outward as shown in figure

1. To reinstall, simply slide back into place and retighten

the screws.

Fig. 2

Содержание PC45











































Результаты поиска

Содержание PC45

Отзывы:

Бренды по названию

Популярные бренды

Harman PC45, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PC45

Отзывы:

Бренды по названию

Популярные бренды