Harman PC45 Скачать руководство пользователя страница 16

Страница: 16 / 42

16 PC 45 Corn/Pellet Stove

Make sure the unit is plugged into a 120 VAC, 60 HZ

electrical source. The power light should be the only

light lit. Anytime there is an interruption in power at the

receptacle, the combustion blower will run for 1 minute

after the power is restored. The control uses this time to

determine exhaust temperature and if there is a need

to remain on.

bE SurE ThErE IS NO FuEl Or OThEr

COmbuSTIblES IN ThE ASh PAN PrIOr TO

lIghTINg.

1.Turn the Mode Selector to "OFF"

2. Fill the hopper with corn or pellets.

3. Clean the burn pot and housing, if necessary.

4. If starting after an empty hopper, turn the feed

adjuster to "TEST" until the fuel is visible in the auger

tube opening. This also allows you to check the motors

for operation.

NOTE: The auger motor will not operate with the view

door or ash door open.

NOTE: The initial start-up on a new stove may require

the corn to be purged into the burnpot area before

continuing to step 5.

5. Turn the feed adjuster to #2 (corn) or #4 (pellet)

6. Flip the igniter switch up into the "AUTO" position.

7. Turn the temperature dial to the desired setting.

8. Turn the mode selector dial to Room Temperature or

Stove Temperature.

9. Fill the hopper with corn or pellets and remove the

ashes as required.

AuTOmATIC STArT uP

"NEVER USE GASOLINE, GASOLINE-TYPE LANTERN

FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR

SIMILAR LIQUIDS TO START OR "FRESHEN UP "

A FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS

WELL AWAY FROM THE HEATER WHILE IN USE".

warning

Fig. 21

CAuTION:

NOT

CONNECT TO ANY AIR

DISTRIBUTION DUCT OR SYSTEM.

NOT

BURN GARBAGE OR FLAMMABLE

FLUIDS SUCH AS GASOLINE, NAPTHA, OR

ENGINE OIL.

HOT WHILE IN OPERATION. KEEP CHILDREN,

CLOTHING, AND FURNITURE AWAY.

CONTACT MAY CAUSE SKIN BURNS.

KEEP FIREBOX AND ASH REMOVAL DOORS

CLOSED DURING OPERATION. MAINTAIN

SEALS IN GOOD CONDITION.

Igniter Switch to "AuTO" (up position)

Starting the Fire

Содержание PC45











































Результаты поиска

Содержание PC45

Отзывы:

Бренды по названию

Популярные бренды

Harman PC45, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PC45

Отзывы:

Бренды по названию

Популярные бренды