Hardi NAVIGATOR 3000 Скачать руководство пользователя страница 66

Страница: 66 / 122

5 - Operation

Safety Precautions - Crop Protection Chemicals

WARNING! Always be careful when working with crop protection chemicals!

WARNING! Always wear proper protective clothing before handling chemicals!

Personal protection

Depending on chemical type, protective gear/equipment should be worn to avoid contact with the chemicals, such as:

•

Gloves

•

Waterproof boots

•

Headgear

•

Respirator

•

Safety goggles

•

Chemical resistant overall

WARNING! Protective clothing/equipment should be used when preparing the spray liquid, during the spray job and
when cleaning the sprayer. Follow the chemical manufacturer’s instructions given on the chemical label.

WARNING! It is always advisable to have clean water available, especially when filling the sprayer with chemicals.

WARNING! Always clean the sprayer carefully and immediately after use.

WARNING! Only mix chemicals in the tank according to directions given by the chemical manufacturer.

WARNING! Always clean the sprayer before changing to another chemical.

Filling Chemicals Through Tank Lid

The chemicals are filled through the tank lid - Note instructions on the chemical container!

WARNING! Be careful not to slip or splash chemicals when carrying chemicals up to the tank lid!

Make sure the spray control unit is switched off.

Set suction SmartValve towards “Suction from main tank”,
Agitation valve towards “Agitation” and pressure SmartValve
towards “Spraying”.

Engage the pump and set P.T.O. revolutions to recommended
pump r.p.m.

Add the chemicals through the main tank hole.

Keep P.T.O. engaged so the spray liquid is continuously agitated
until it has been sprayed on the crop.

Содержание NAVIGATOR 3000



























































































































Результаты поиска

Содержание NAVIGATOR 3000

Отзывы:

Hardi NAVIGATOR 3000, Руководство оператора, Страница: 66 / 122

Результаты поиска

Содержание NAVIGATOR 3000

Отзывы: