manualshive.com logo in svg

Hardi NAVIGATOR 3000, Руководство оператора, Страница: 6 / 122

Поделиться
Скачать
Hardi NAVIGATOR 3000 Скачать руководство пользователя страница 6

Table of Contents

4

Support jack  ........................................................................................................................................................................................................... 35
Jack up the sprayer  ............................................................................................................................................................................................ 36

Transmission shaft  ..............................................................................................................................37

Operator’s safety .................................................................................................................................................................................................. 37
P.T.O. installation .................................................................................................................................................................................................. 37

Mechanical connections  ......................................................................................................................39

Hitch - adjustment  ............................................................................................................................................................................................. 39
Hitch - adjustment (Navigator 6000)  ...................................................................................................................................................... 39
Swivel hose support .......................................................................................................................................................................................... 39

Hydraulic systems  ...............................................................................................................................40

General Info  ............................................................................................................................................................................................................ 40
Requirements - tractor (SPB/SPC HY-model) ..................................................................................................................................... 40
Requirements - tractor (SPB/SPC HZ-model) ..................................................................................................................................... 40
Requirements - tractor (DTZ model) ....................................................................................................................................................... 40
Hydraulic Motor for Liquid Pump  ............................................................................................................................................................. 41
Open center hydraulics ................................................................................................................................................................................... 42

Electrical Connections  .........................................................................................................................43

Power supply  ......................................................................................................................................................................................................... 43
Control units  .......................................................................................................................................................................................................... 43
Installation of control unit brackets ......................................................................................................................................................... 44
Speed Sensor for Sprayer ............................................................................................................................................................................... 44
Road traffic lights ................................................................................................................................................................................................. 44

Liquid system  ......................................................................................................................................45

CycloneFilter .......................................................................................................................................................................................................... 45

Transport .............................................................................................................................................46

Adjusting boom transport position ......................................................................................................................................................... 46

Track width, axles and wheels  .............................................................................................................47

Altering the track width (optional combo axle)  .............................................................................................................................. 47
Changing the wheel offset  ........................................................................................................................................................................... 47
Dual tire setup (optional)  ............................................................................................................................................................................... 48

Boom ...................................................................................................................................................49

Suspension effect adjustment (80’-100’ SPC only) ......................................................................................................................... 49

5 - Operation

Boom ...................................................................................................................................................51

Safety info  ................................................................................................................................................................................................................ 51
Maneuvering of the SPB and SPC booms - HY-versions ............................................................................................................. 51
Maneuvering of the SPB, 80’-100’ SPC booms - (ISOBUS / HC 8600 / HC9600) ........................................................... 52
Maneuvering of the SPB and SPC booms - HZ-versions  ............................................................................................................ 53
Single-sided folding (All HZ versions except Dual Fold)  ............................................................................................................ 53
Maneuvering of the 90’/60’ SPC Dual Fold boom - HZ ............................................................................................................... 54
Single-sided folding of the 90’/60’ SPC Dual Fold boom ........................................................................................................... 55
Maneuvering of the 120’/90’ SPC Dual Fold boom - HZ  ............................................................................................................ 56
Maneuvering of the 80’-132’ DTZ Booms - (ISOBUS / HC 8600 / HC9600)  ..................................................................... 57
Boom Tilt Function ............................................................................................................................................................................................. 58
Night Spraying Light (Platform mounted lights) ............................................................................................................................. 58
Night Spraying Light (Boom mounted lights)  .................................................................................................................................. 59

Liquid System  ......................................................................................................................................60

Filling/washing location requirements  ................................................................................................................................................. 60
Filling of water  ...................................................................................................................................................................................................... 60
Filling through tank lid  .................................................................................................................................................................................... 60
Filling of main tank using Quick fill .......................................................................................................................................................... 61
Filling of Rinse Tank using Quick fill ......................................................................................................................................................... 61
Filling of Clean Water Tank ............................................................................................................................................................................ 62
Adjustment of EVC operating unit ........................................................................................................................................................... 63
Safety Precautions - Crop Protection Chemicals ............................................................................................................................. 64
Filling Chemicals Through Tank Lid  ........................................................................................................................................................ 64
Operating the TurboFiller  .............................................................................................................................................................................. 65
Filling liquid chemicals by HARDI® TurboFiller (optional) .......................................................................................................... 66

Содержание NAVIGATOR 3000



























































































































Отзывы:

Нет отзывов