HappyJapan HCD3E Скачать руководство пользователя

Страница: 5 / 362

-CD -5

IMPORTANT SAFETY INSTRUCTIONS

1_1 F701

1-1

When using an electrical appliance, basic safety precautions should always be followed, includ-

ing the following.

Read all instructions before using this appliance.

DANGER

- To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in. Always unplug this appliance

from the electric outlet immediately after using and before cleaning.

WARNING

- To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this appliance is used

by or near children.

2. Use this appliance only for its intended use as described in this manual. Use only

attachments recommended by the manufacturer as contained in this manual.

3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into water. Return the appliance to the nearest

authorized dealer or service center for examination, repair, electrical or mechanical

adjustment.

4. Never operate the appliance with any air openings blocked. Keep ventilation openings of the

sewing machine free from the accumulation of lint, dust, and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

8. To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10.Keep fingers away from all moving parts. Special care is required around the sewing

machine needle.

11.Always use the proper needle plate. The wrong plate can cause the needle to break.

12.Do not use bent needles.

13.Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14.Switch the sewing machine off (“0”) when making any adjustments in the needle area, such

as threading needle, changing needle, threading bobbin, or changing presser foot, etc.

15.Always unplug sewing machine from the electrical outlet when removing covers, lubricating,

or when making any other user servicing adjustments mentioned in the instruction manual.

SAVE THESE INSTRUCTIONS

Содержание HCD3E











































































































































































































































































































































































Результаты поиска

Содержание HCD3E

Отзывы:

Похожие инструкции для HCD3E

Бренды по названию

Популярные бренды

HappyJapan HCD3E, Инструкция

Результаты поиска

Содержание HCD3E

Отзывы:

Похожие инструкции для HCD3E

Бренды по названию

Популярные бренды