HappyJapan HCD3E страница 74 Скачать руководство пользователя

Страница: 74 / 362

-DA -53

7-A

CAP FRAME option

7-A M717

7. Remove the cap holder frame from the cap

stretcher.

8. As shown in Fig. 5, install the cap frame on

cap in the drive frame.

Rotate the cap frame as show in the Fig 5 so

that the brim of the cap cannot hit the

machine. Then, push the holder lever in the

3 places shown in the arrow in Fig. 5, and

install the cap frame in the cap drive frame

so that so that the center guide of the drive

frame fits the concave area of the cap frame.

Confirm that the cap frame is firmly installed on

the cap drive frame without any gap.

Clip

Lever for clip

6. As shown in Fig. 4, tip the cap

stretcher forward.

Clip the back of the cap and

nonwoven fabric in two places.

Make the clip livers face each other.

Fig. 4

Fig. 5

Hold

lever

Cap drive

frame

Center

guide

If there is a gap between the cap frame and the

cap frame drive or the holder lever does not fit

the hole of the cap frame, adjust loosen the set

screw on the hold lever to adjust the position.

Содержание HCD3E











































































































































































































































































































































































Результаты поиска

Содержание HCD3E

Отзывы:

Похожие инструкции для HCD3E

Бренды по названию

Популярные бренды

HappyJapan HCD3E, Инструкция

Результаты поиска

Содержание HCD3E

Отзывы:

Похожие инструкции для HCD3E

Бренды по названию

Популярные бренды