background image

Four  post  parking  lift                                                                                       Happ25  4  post  hoist

 

 

23 

10  

Check  the  chain,  the  steel  cable  
wheel  if  their  rotation  are  normal     

Operation  
and  
visual  

Oiling  Lubricating

cleaning

new  

replacement  

11  

Check  up  and  down  movement  of  
two  landslide  is  normal,  comfortable  
and  non-­jitter  

Operation   Foreign   body   cleaning

oiling  

cleaning  

12  

Check  the  action  of  the  four  
insurance  block  if  it’s  normal  and  
comfortable  (with  automatic  insert  
action),  check  the  insurance  steel  
cable  if  it’s  loose  injury     

Operation

visual

listen  

Foreign   body   cleaning

oiling  

cleaning

adjustment   or   new  

replacement     

13  

Whether  it  is  automatically  stopped  
when  no-­load  up  to  the  highest  
location     

Operation   Repair

new  replacement  

14  

Check  power  unit  is  working  properly  
without  abnormal  noise  

Operation

listen  

Repair

new  replacement  

15  

Inspect  tanks,  oil  hoses  and  
connecting  joints  is  normal  no  
leakage     

Operation

visual  

Repair

new  replacement  

6.   

Packing,  transport  and  storage

      

Only  skilled  personnel  who  are  familiar  with  the  lift  and  this  manual  shall  be  allowed  to       
carry  out  packing,  lifting,  handling,  transport  and  unpacking  operations.  
  
90%   of  components  were  pre-­assembled  and  packed  with  blister  packing  in  steel  frame  
for  shipment.  Power  unit  was  packed  together   with   the   lift,   and   power   unit   stand   was  
packed  and  fixed  on  above  lifts.                                                                       
  
Lifting  and  handling.  When  loading/unloading  or  transporting  the  equipment  to  the  site,be  
sure  to  use  suitable  loading  (e.g.  cranes,trucks)  and  hoisting  means.  Be  sure  also  
to  hoist  and  transport  the  components  securely  so  that  they  cannot  drop,  taking  into  
consideration  of  the  package’s  size,  weight  and  centre  of  gravity  and  its  fragile  parts.      
  
Storage  and  stacking  of  packaged  lifts.     
Packaged  lifts  must  be  stored  in  a  covered  place,  out  of  direct  sunlight  and  at  a  
temperature  between-­10°C  and  +40°C.    

Delivery  and  check  of  packages.  When  the  lift  is  delivered,  check  for  possible  damages  
due  to  transport  and  storage;;  verify  whether  the  points  are  included  which  is  specified     
in  the  manufacturer’s  confirmation  of  order.  In  case  of  damage  in  transit,  the  customer     
must  immediately  inform  the  carrier  of  the  problem.  Packages  must  be  opened  carefully,  
not  to  cause  damage  to  people  (keep  a  safe  distance  when  opening  straps)  and  parts  of     
the  lift  (be  careful  the  objects  do  not  drop  from  the  package  when  opening).    

   

Содержание Happ25











































Отзывы: