Hangar 9 F-22 Raptor ARF Скачать руководство пользователя

Страница: 14 / 56

Items Required

• Wing (left and right)

• Linkage stay (2)

• Clevis w/retainer (2)
• Pushrod wire, 4

-inch (121mm) (2)

Tools Required

• 12-minute epoxy

• Felt-tipped pen

• Pliers

• Medium sandpaper

• Paper towel

• Rubbing alcohol

• Masking tape

• Z-bend pliers

The F-22 Raptor can either be built using

fixed flaps or operating flaps. The following

covers the installation of fixed flaps and how

to position them depending on your flying

skills. Information on setting the position

of the flap linkage is coverd on Page 17,

Setting the position of the fixed flaps



Step 1

Use medium grit sandpaper to roughen both sides

of the flap stay.



Step 2

Use a paper towel and rubbing alcohol to remove any grit

or oils from the flap stay.



Step 3

Test fit the flap stay in position in the wing. Note the

position of the holes in the stay. The hole closest to the

wing faces towards the leading edge of the wing. The hole

farthest from the wing faces the flap.

Section 2: Fixed Flap Installation

Содержание F-22 Raptor ARF

























































Результаты поиска

Содержание F-22 Raptor ARF

Отзывы:

Похожие инструкции для F-22 Raptor ARF

Бренды по названию

Популярные бренды

Hangar 9 F-22 Raptor ARF, Инструкция по сборке

Результаты поиска

Содержание F-22 Raptor ARF

Отзывы:

Похожие инструкции для F-22 Raptor ARF

Бренды по названию

Популярные бренды