Hangar 9 F-22 Raptor ARF страница 46 Скачать руководство пользователя | Manualshive

Страница: 46 / 56

background image

46



Ailerons

Turn on the transmitter, then the receiver. Move the aileron

stick to the right, which is the input for a right turn. The

right aileron will move up, and the left aileron will move

down. If not, check the radio instructions on how to

reverse the direction electronically at the transmitter.



Elevator

With the radio system still on, pull back on the elevator

control stick to give an up elevator input. The elevator

should move up from center. If not, check the radio

instructions on how to reverse the direction electronically

at the transmitter.

Section 12: Checking the Control Surface Directions

«
...
44
45
46
47
48
...
»

Содержание F-22 Raptor ARF

























































Отзывы:

Нет отзывов

Похожие инструкции для F-22 Raptor ARF

Бренд: Badger Basket Страницы: 4

Бренд: Quest Engineering Страницы: 2

Бренд: Jabiru Страницы: 298

Бренд: J. Perkins Страницы: 14

Бренд: J-Power Страницы: 24

Бренд: Fisher-Price Страницы: 2

Lokpuffer Puff-H0

Бренд: Fichtelbahn Страницы: 2

Бренд: Fisher-Price Страницы: 6

Бренд: Quick Страницы: 32

Бренд: J. Perkins Страницы: 12

Wattage Thermalaire EP

Бренд: Academy of Model Aeronautics Страницы: 28

Бренд: Hot Wheels Страницы: 4

Бренд: marklin Страницы: 20

Бренд: Spin Master Страницы: 3

Бренд: Solly Systems Страницы: 56

Бренд: Wilhelm Schroder Страницы: 4

Бренд: Eduard Страницы: 7

Бренд: Ravensburger Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды