Hangar 9 F-22 Raptor ARF страница 19 Скачать руководство пользователя

Страница: 19 / 56

You can take your F-22 Raptor ARF even a step further

and add functional flaps. Simply remove the covering over

the flap servo openings in the wing panels, secure the

servos to the flap servo hatches, and secure the hatches to

the wing. Basically, the same procedure as installing the

aileron servos. Hook up the linkage to the servo following

the directions and you have a scale F-22 Raptor complete

with functioning landing flaps.

Note

: Using two standard rotation servos and a standard

Y-harness for the flap servos will result in them moving in

opposite directions instead of the same direction. There

are three options available that will result in the flaps

operating correctly.

Option 1

: Use two JR SPORT

ST47 (JSP20050) servos

and two 6-inch Servo Extensions (JSP98020) if your

radio has programmable mixing. You will need to use two

separate channels and use your radio to mix them together

electronically for this option to work.

Option 2

: Use two JR SPORT

ST47 (JSP20050) servos,

two 6-inch extensions and a JR

MatchBox

™

or a 6"

standard reversing Y-harness (EXRA320) to link the two

flap servos to operate properly.

Option 3

: Use a JR SPORT

™

ST47 (JSP20050) standard

servo and JR SPORT ST47 (JSP20050R) reverse servo

and a standard Y-harness.

Items Required

• Wing (left and right)
•#2 x 3/8-inch screw (8)
• Flap servo hatch (left and right)
• 3/8 x 3/4 x 3/4-inch (9.5 x 19 x 19mm)

servo mounting block (4)

• Pushrod wire, 4

-inch (121mm) (2)

Tools Required

• 12-minute epoxy

• Felt-tipped pen

• Drill bit: 1/16-inch (1.5mm) • Drill
• Y-Harness (JSP98020)

• Hobby knife

• Phillips screwdriver (small)
• Razor saw
• Long Servo Arm (JRPA212) (2)



Step 1

Remove the covering from the servo opening in the

bottom of the wing using a hobby knife. Use a trim

iron to seal the edges of the UltraCote

covering into

the opening.



Step 2

Select the correct servo hatch by checking the alignment

for the servo arm on the plate with the one on the wing.

Section 3: Flap Servo Installation

Содержание F-22 Raptor ARF

























































Результаты поиска

Содержание F-22 Raptor ARF

Отзывы:

Похожие инструкции для F-22 Raptor ARF

Бренды по названию

Популярные бренды

Hangar 9 F-22 Raptor ARF, Инструкция по сборке

Результаты поиска

Содержание F-22 Raptor ARF

Отзывы:

Похожие инструкции для F-22 Raptor ARF

Бренды по названию

Популярные бренды