Hangar 9 F-22 Raptor ARF Скачать руководство пользователя | Manualshive

Страница: 28 / 56

background image

28



Step 8

Slide the washer onto the engine shaft and then thread the

spinner adapter onto the engine shaft. Rotate the propeller

clockwise so it is resting against the lugs of the spinner

backplate. Finger-tighten the adapter.

Note

: You will not use the nut from your

engine for this application. Make sure to save

the nut somewhere in case you use the engine

from your F-22 Raptor in a future project.



Step 9

Use an adjustable wrench to tighten the propeller nut.

Make sure the propeller remains against the lugs on

the spinner backplate.

Important

: DO NOT use pliers, as the nut will

not be tight enough and could come loose.



Step 10

Locate the spinner cone and position it onto the spinner

backplate. The cone will key to the backplate with no gap

between the backplate and cone.



Step 11

Slide the adapter screw through the hole in the end of the

spinner and thread it into the adapter. Use the included

hex wrench to tighten the screw. Do not over-tighten the

screw which could possibly deform the spinner.

Section 5: Cowling Installation

«
...
26
27
28
29
30
...
»

Содержание F-22 Raptor ARF

























































Отзывы:

Нет отзывов

Похожие инструкции для F-22 Raptor ARF

Super Decathlon 40

Бренд: GREAT PLANES Страницы: 44

He 111H-6 nose interior

Бренд: Eduard Страницы: 6

KICK`N CRAWL BARN 71699

Бренд: Fisher-Price Страницы: 4

Бренд: THUNDER TIGER Страницы: 28

Бренд: Global Hobby Страницы: 32

Бренд: LEGO Страницы: 36

Deere CONSTRUCTION LOADER

Бренд: Peg-Perego Страницы: 52

Touch & Learn Activity Desk Deluxe

Бренд: VTech Страницы: 10

JAMMIN' JEEP T8396

Бренд: Barbie Страницы: 24

Бренд: Majik Страницы: 8

Dystraction backyard /Indoor F3A

Бренд: Stevens AeroModel Страницы: 19

Бренд: Raptor Страницы: 41

3-IN-1 CLASSIC AMUSEMENT PARK

Бренд: K'Nex Страницы: 24

Education RENEWABLE ENERGY WATER POWERED...

Бренд: K'Nex Страницы: 20

PENNSYLVANIA K4 STREAMLINER

Бренд: Lionel Страницы: 2

Mercedes-Benz SLK

Бренд: Rastar Baby Страницы: 14

Royal Hudson Steam Engine

Бренд: Rail King Страницы: 24

Бренд: Dromida Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды