Hampton®H15E-11DirectVentFreestandingGasStove
| 29
installation
Outside
Wall
Mur extérieur
Furring
Strips
Fourrures en bois
Furstrp.eps
see also c34020a.eps
furstrpf.eps
french
Note: The pipe seam should be facing down.
Note: To make the installation more aes-
thetically pleasing, we recommend
framing out a square that the cap can
be mounted on.
3) Attachthe4"dia.flexlinertotheventterminal
ensuringthattheflexoverlapsthecollarofthe
ventterminalbyaminimumof1-3/8"(35mm).
UseMill-Pactosealandsecurewith3ofthe
#8x1/2"screws(stainlesssteel).
4) Attachtheadjustablepipesectiontothevent
terminalusingMill-Pacandattachwith3ofthe
#8x1/2"screws(stainlesssteel).
NOTE: For best results and optimum perfor-
mance with each approved venting sys-
tem, it is highly recommended to apply
“Mill-Pac” sealant (supplied) to every
inner pipe connection. Failure to do so
may result in drafting or performance
issues not covered under warranty.
Note: If installing termi-
nation on a siding
covered wall, a vinyl
siding standoff or
furring strips must
be used to ensure
that the termination
is not recessed into
the siding. For vinyl
siding standoff installation refer to the
Dura-Vent Termination instructions.
5) Slide the partially connected pipe and vent
terminal assembly through the wall thimbles
(fromtheexteriorintotheinterior)andsecure
thecaptotheexteriorwallwith4ofthesupplied
screws(#8x1-1/2"drillpoint,stainlesssteel).
Note:pilotholeswillneedtobedrilledthrough
thewallthimbleonall4corners.
Note: The four screws provided for the vent
cap should be replaced with appropriate
fasteners for stucco, brick, concrete, or
other types of sidings.
6) Abeadofnon-hardeningmasticshouldberun
around both the termination and vinyl siding
standoff to prevent water from entering and
tomakeatightsealbetweenthecapandthe
standoff.
7) Stretchthe4"dia.flexlineroutfullyandgeta
trialfitofthelinerontothe4"dia.startercollar.
8) Cutthe4"dia.flexlinertothedesiredsize.
Hint:
leaveanextra12"to16"oflength,thiswillmake
thefinalassemblyeasiertoworkwith.
9) Securethe4"dia.flexlinertothe4"adapterwith
Mill-Pacand3ofthe#8x1/2"screws(stainless
steel).
10)Slide the decorativeThimble Cover over the
pipesectionsandsecurewith4screws(#8x
1-1/2"drillpoint,black)tothewall.
11)Slide the 90
o
elbow (crimp end up), the 45
o
elbowandthe4ft.pipesection(crimpendup)
overthe4"dia.flexliner.
12)Installthespringspacersontothepipesections.
13)Securethe4"dia.flexlinerwithadapteronto
thestovecollar.PutabeadofMill-Pacaround
theapplianceadapterandsecurewith3screws
(#8x1/2,stainlesssteel).
14)Attachthe45
o
elbowontothestartercollarby
sealingwithMill-Pacsecuringwith3ofthe#8
x1/2"(black)screws.
15)Attach the pipe section to the 45
o
elbow by
sealingwithMill-Pacsecuringwith3ofthe#8
x1/2"screws(black).Pipeseamsshouldbe
facingthewall.
16)Attachthe90
o
elbowontothepipesectionby
sealingwithMill-Pacsecuringwith3ofthe#8
x1/2"screws(black).
17)Slidetheadjustablepipesectionontothe90
o
elbow.Slidethetrimcollarovertheadjustable
pipesectionstocoverthejointofthetelescopic
section.Theflexmayhavetobecompressed
backinorderfortheadjustablepipetoproperly
matetotheelbow.SealwithMill-Pacsecure
with 3 of the #8 x 1/2" screws (black). Pipe
seamsfacingdown.
18)Installthetrimcollaroverthestartercollarand
securewitha#8x1/2"screw(black).
Ifthepipeneedstobetouchedup,useonlyStove
BriteHighTemperatureMetallicBlackStovePaint.
