Haier GE GDF450P R0 Series Скачать руководство пользователя страница 59

Страница: 59 / 61

– 59 –

Fault

Code

Load to Control

Action Items

F151

Continuous Flow Fault

The control has detected the pressure sensor at a flood

stage. Check for stuck open water valve or continuous

voltage to the valve.

F152

Continuous Heater

The control has detected a stuck heater relay. Cycle

Power. Update Software. Replace control if the fault

reoccurs.

F153

Door Latch Failed

Check harness connections to door latch and control.

Check Door latch.

F154

Door Latch Diagnostic

Replace machine control board.

F155

Tactile Key Stuck

Check button operation, each button should "click".

Check for plastic flash. Replace User Interface board.

F158

Overvoltage

An overvoltage condition has been detected by the

control. Check incoming power supply for correct

voltage levels.

F159

Circulation Pump Fuse Fault

The control has detected a blown fuse on the machine

control board to the circulation pump and the machine

control board.

Demo Mode

Entering/Exiting Demo Mode:

For Models with 1 or 2 Pads:

Models with 1 or 2 pads do not have a Demo Mode.

For Models with 3 or More Pads:

Press the Dry and Start pads together momentarily within 5 minutes

of powering on the unit.

Sabbath/Door Wake Up Mode

Entering/Exiting Demo Mode:

For All Models:

To turn this option ON/OFF, press the Cycle Select and Wash Temp pads together for

5-seconds, close the door and wait 3-minutes for the dishwasher to go into sleep mode. In the OFF

mode, the control display, control sounds, and interior lights (on some models) will not respond to the

door opening/closing. To activate the control and interior lights (on some models), press any pad.

Содержание GE GDF450P R0 Series






























































Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды

Haier GE GDF450P R0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды