Haier GE GDF450P R0 Series Скачать руководство пользователя

Страница: 34 / 61

– 34 –

Heat Element Removal

The heater may be removed by one of two

methods. The first method requires door and

sump removal to gain access to the element nuts.

The second method requires the dishwasher be

removed from its installation.

Element Removal Without Uninstalling the

Dishwasher

1. Disconnect power to the dishwasher.

2. Remove the lower rack.

3. Remove the door.

4. Remove the sump assembly.

5. Disconnect the two wire leads to the heater.

6. Remove the two 15/16-inch heater nuts.

7. Remove the heater from inside dishwasher

by tilting up the rear and pull forward to

the front to slide out of the heater support

brackets.

Element Removal by Uninstalling the

Dishwasher

1. Disconnect power to the dishwasher.

2. Remove the lower rack.

3. Remove the door.

4. Remove the dishwasher from its installed

position and place on its back.

WARNING

: If the door is not removed and the

dishwasher is not placed on its back, there is a

TIP RISK.

5. Disconnect the two wire leads to the

heater.

6. Remove the two 15/16-inch heater nuts.

7. Remove the heater from inside the

dishwasher.

When reinstalling the element, the ground bracket

must be in place and the heater nut with the

ground clip must be installed on the left side (as

viewed from the front or right side if viewed from

the rear).

Содержание GE GDF450P R0 Series






























































Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды

Haier GE GDF450P R0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды