Haier GE GDF450P R0 Series Скачать руководство пользователя

Страница: 56 / 61

– 56 –

Service Mode can only be entered during

Error Mode.

NOTE

: Entering Service Mode resets the CSM.

The dishwasher must be in Consumer Error Mode

to enter Service Mode. Entering Service Mode

will reset the CSM, allowing loads to be checked

for the cause of the CSM to trip.

For Models with 1 or 2 Pads

Press Start. Service Mode will then run through

all tests on its own. Skip to the next test by

pressing start. Depending on the model, the

Normal or Heavy LED will flash per the chart

below.

Exiting Service Mode

For models with 1 or 2 pads, both Error Mode

and Service Mode exits automatically or will time-

out after approximately 5 minutes.

For Models with 3 or More Pads

Press and hold the furthest most pad on the left

for 5 seconds. Pressing the furthest most pad on

the left will select the test. Press the Start pad

to cancel the test, or press the furthest most pad

on the left to cancel the current test and proceed

to the next test. Depending on the model, the

Normal or Heavy LED will flash per the chart

below.

Exiting Service Mode

For models with three or more pads, press the

furthest most pad on left and Start pads together

momentarily or will time-out after approximately 5

minutes.

Start

LED

Blinks

Load to

Control

Timeout / Notes

Drain

Pump

Attempts to

automatically empty tub.

Takes appx. 75 seconds

from normal level.

Water

Valve

Attempts to

automatically fill tub to

normal volume. Takes

appx. 1 minute.

Circulation

Pump

Changes spray arm

(via changing diverter)

every 30 seconds.

Runs for maximum of 2

minutes.

Heater

Turns heater on for

maximum of 2 minutes.

Detergent

Module

Turns soap dispense

solenoid on for

maximum of 2 minutes.

Heater

Relay

Turns Calrod heater

relay on for maximum

of 2 minutes. Turns off

neutral break to allow

the board to test the

CSM.

Start

LED

Blinks

Load to

Control

Timeout / Notes

Water

Valve

Attempts to fill to

normal level. Takes

approximately 1 minute.

Detergent

Module

Turns on detergent

module solenoid for a

maximum of 2 minutes.

Circulation

Lower

Runs lower spray arm

for approximately 1

minute.

Circulation

Upper

Runs upper spray arm

for approximately 1

minute.

Heater

Turns on heater and

circulation pump for a

maximum of 1 minute.

Drain

Pump

Runs drain pump until

pressure sensor sees

an empty tub.

Service Mode

Содержание GE GDF450P R0 Series






























































Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды

Haier GE GDF450P R0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды