Haier GE GDF450P R0 Series Скачать руководство пользователя

Страница: 54 / 61

– 54 –

Detergent Module Diagnosing

1. Remove power to dishwasher.

2. Remove toe kick panel.

3. Disconnect door harness.

4. Remove and separate the door.

5. The inner panel may be set into the

dishwasher and latched in the closed position.

6. Reapply power.

7. Place the dishwasher into Service Mode (see

Service Mode

section in this service guide),

then activate the detergent test to check for

13.5 VDC to the detergent module. Service

Mode will provide a 15-second activation time.

Detergent Dispenser Removal

1. Remove power to the dishwasher.

2. Remove and separate the door.

3. Remove the EPS cover, double back tape

is used to secure and is reusable (when

reinstalling the EPS cover, UP must be

toward the top of the door).

4. Remove six 1/4-inch hex-head screws.

5. Mounting plate removes from inside the door.

Mounting Plate

Door Strike

The door strike is attached to the inner door panel.

Door Strike Removal

1. Remove and separate the door.

2. Remove the control console or control panel.

3. Remove the 1/4-inch screw holding the

strike and lift up to remove the door strike (a

Phillips-head screw will come with the service

part for easier installation).

6. The detergent module can now be removed

from the inner door panel.

Содержание GE GDF450P R0 Series






























































Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды

Haier GE GDF450P R0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды