Haier GE GDF450P R0 Series Скачать руководство пользователя

Страница: 37 / 61

– 37 –

Structure

The tub and structure section of this guide will

cover the toe kick, junction box, racks, leveling

legs, door balance, gaskets, main control board,

door, door components, as well as the removing

and separation of the screwless appearance door.

It will also cover the sump module and removal.

Details of the sump components will be covered

in the

Circulation System

Drain System

sections of this service guide.

WARNING: GEA Factory Service Technicians

are REQUIRED to follow Lockout / Tagout

(LOTO) 6 Step Process prior to beginning

repair.

Toe Kick

The toe kick is a decorative panel covering the

machine area of the dishwasher. The panel

provides a safety barrier, closing the front of the

dishwasher machine compartment. The toe kick

prevents injury from electrical components under

the dishwasher. To remove the panel, remove

two 1/4-inch hex-head screws and pull the panel

away from the dishwasher.

Junction Box and House Wiring

Connection

The junction box is located behind the toe kick

on the right-hand side of the dishwasher. The

junction box is where the 120 VAC house voltage

connects to the dishwasher. The dishwasher

may be hardwired or an optional cord may

be installed (available separately,

Part #

WX09X70910), which plugs into a wall outlet and

connects to the harness plug into the control (see

the separate Installation instructions for more

information). The cover is held in place with a

1/4-inch hex-head screw on the left side, and tab

on the right side. To remove the cover, remove

the screw and pull out and left to release the tab.

Insulation Toe Kick Toe Kick Screws

Содержание GE GDF450P R0 Series






























































Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды

Haier GE GDF450P R0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды