Haier GE GDF450P R0 Series Скачать руководство пользователя

Страница: 28 / 61

– 28 –

WARNING: GEA Factory Service Technicians

are REQUIRED to follow Lockout / Tagout

(LOTO) 6 Step Process prior to beginning

repair.

Use the flat-blade screw-driver to remove the

floating seal from the sump, using care not to

damage the inside sealing surface.

(

Continued next page

)

The circulation motor is a DC Brushed Motor; it

has onboard AC to DC rectification. Resistance

cannot be properly checked on this motor

because of the rectifier and diodes inside the

motor shield.

Circulation Pump Motor Assembly Removal

1. Disconnect power to the dishwasher.

Remove the toe kick panel, door, and sump

(see

Door Removal

under the

Door

section

of this service guide, and

Sump Module

Removal

under

Sump Module

, in the

Tub

section of this guide).

2. Loosen the outlet wash motor (diverter) clamp.

Use a large flat-blade screw-driver to slide the

circulation motor out of the floating seal. As

the pump assembly is removed from the seal,

slide the wash motor off of the hanger (use

care to not lose the hanger grommet), and

remove and discard the one time use clamp.

Floating Seal Sealing Surface

Pump Assembly Grommet

Circulation Motor and Pump Assembly

Clamp Removal Tip

: Use a small screw-driver

inserted into the ear of the clamp and move the

handle back and forth to loosen the clamp. The

clamp can be removed and discarded when the

component is removed. The clamp kit (

Part #

WD02X25470) contains a single clamp for the

diverter connection.

Содержание GE GDF450P R0 Series






























































Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды

Haier GE GDF450P R0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды