Haier GE GDF450P R0 Series Скачать руководство пользователя страница 40

Страница: 40 / 61

– 40 –

Fill Funnel and Hose

The

fill funnel is located on the left side of the

dishwasher tub. There is a gasket between the

fill funnel and the tub. The fill hose connects the

water valve to the fill funnel.

Fill Funnel Removal

1. Remove power to the dishwasher.

2. Uninstall dishwasher from installation.

Disconnect fill hose by gently pulling down

from the fill funnel and remove 1/4-inch hex-

head screw. Rotate fill funnel clockwise (CW)

(twist lock design).

(

Continued next page

)

Testing the

Pressure Sensor

: To verify the

pressure sensor is receiving power, remove the

connector from the sensor and test for 5 VDC

between pin 2 (+) and pin 3 (-) on the sensor. To

verify the sensor is properly sending the water

level signal to the machine control, test for

frequency (0 to 5 VDC) between pin 7 (+) and

pin 6 (-) on the machine control connector J603.

Use the chart under

No Fill Diagnostics

later in

this section to determine if the output frequency

corresponds to the water level observed inside

the dishwasher.

NOTE

When flood trip point is reached (40.11 to

39.69 Hz), the drain pump will turn on.

Pressure Switch Removal

1. Remove power to the dishwasher.

2. Remove the toe kick.

3. Carefully pull the locking tab toward the

body and turn the pressure switch counter-

clockwise (CCW) while pulling the switch out.

4. Remove the harness from the sensor.

Содержание GE GDF450P R0 Series






























































Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды

Haier GE GDF450P R0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды