Haier GE GDF450P R0 Series Скачать руководство пользователя

Страница: 25 / 61

– 25 –

• Spray Arm Rotation

With only 0.75 to 0.95 gallons of water, filtration is the start of improved performance. Water is cleaned

through the fine and ultra-fine filters before it enters the main pump. Water must also flow through the

Piranha Hard-Food Disposal and finally into the wash pump assembly. Clean filtered water then flows

into the diverter system which directs it to either the lower spray arm or mid spray arm. Water is jetted

through more jets and with more power due to different wash zones created by the diverter.

The new 2021 Plastic Tub Value Model Dishwasher features alternating spray arms allowing low water

use, helping energy efficiency. A diverter system is used to isolate the wash arms and is controlled by

cycling the wash pump as described later in this section. Filtration has been greatly improved to allow

clean filtered water to circulate during wash. The fine and ultra-fine filters are consumer removable and

cleanable.

Specifications

•

Single Speed Circulation Pump

: 120 VAC, .8 amps – 3.8 LRA, 8 GPM @ 5PSI

• Heater

: 120 VAC, 18 ohms wet – 28.8 ohm dry, 6.67 amp wet -4.17 dry, Watts 800 wet /500 dry +/-

•

Detergent Cup

: 13.5 VDC, 25 ohms, .5

second to release detergent cup, 15 seconds

to release Rinse Aid (see the

Door

section of

this service guide).

•

Thermistor

Spray Arm RPM

Lower

50 RPM CW +/- 10%

Middle

30 RPM CCW +/- 10%

: Clockwise

CCW

: Counter-Clockwise

Circulation System

Содержание GE GDF450P R0 Series






























































Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды

Haier GE GDF450P R0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF450P R0 Series

Отзывы:

Похожие инструкции для GE GDF450P R0 Series

Бренды по названию

Популярные бренды