Habasit PMR-07 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 68

Habasit PMR-07 Скачать руководство пользователя страница 11

Habasit Italiana S.p.A.
Vittorio Veneto 31029 (TV)
Tel.: ++39(0)438.9113
Fax. ++39(0)438.200545

Regulating Unit PMR-07

Author:

A.T. / KM

REGULATIONS AND GENERAL WARNING NOTES

Edition: 04/2006

Page

A-5

Replaces: 10/2005

A.4

GUARANTEE CONDITIONS

A.4.1

G

UARANTEE TERMS AND VALIDITY

The manufacturer guarantees the product against any faults either in materials or in
workmanship, for 2 (two) years from the date of installation of the product at the buyer’s
premises. In this case, the manufacturer shall limit itself to replacing or repairing any part or
parts returned to the manufacturer, which was/were found to be faulty.
Furthermore, the manufacturer, may, at its discretion, replace or repair any part or parts,
returned by the buyer, which, subject to the manufacturer’s confirmation, are found to be faulty.
The following shall be charged to the buyer and/or its customer: transport costs and other
handling costs of parts returned to the manufacturer.
The manufacturer shall have the sole right to decide if such parts shall be repaired or replaced.
In no other case shall the manufacturer be responsible for collateral or incidental damage.
The guarantee does not apply to systems that were repaired by third parties NOT authorized by
the manufacturer.
Spare parts supplied by the manufacturer must be used. Any deviation from this rule will mean
the guarantee will not apply.

A.4.2

W

HEN THE GUARANTEE CAN BE VOIDED

The manufacturer's guarantee for the equipment may be annulled as a result of improper
intervention or repairs.
The manufacturer's guarantee for the equipment may be annulled as a result of the use of
improper materials or materials not supplied by the manufacturer.
The instructions in this manual must be observed to prevent the guarantee cover from being
voided.

IMPORTANT

HABASIT CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED BY IMPROPER,

INCORRECT AND UNREASONABLE USE OF THE REGULATING UNIT.

Regulating Unit PMR-07

«
...
9
10
11
12
13
...
»

Содержание PMR-07





































































Отзывы:

Нет отзывов