Haas Bar Feeder Скачать руководство пользователя

Страница: 13 / 13

Haas Bar Feeder - Calibration Instructions

Perform this procedure one time at installation. The Run/Setup Key Switch must be in Setup Mode to calibrate the

EOB Switch.

The bar feeder installation is complete. Refer to the

HAAS BAR FEEDER - NGC LATHE SETUP

procedure to setup the

bar feeder.

Press

[RECOVERY]

button to enter the bar feeder

recovery mode.

Place a precision ground calibration bar with a

known length on the charging table.

Press

[ORIGIN]

, type in the length of the

calibration bar and press

[ENTER]

The pusher clears the tray then loads the

calibration bar. It will then measure the length of

the bar and apply the calibration.

Remove and properly store the calibration bar for

future use. A bar feeder only needs calibration at

installation, or if the EOB sensor, home switch, or

trolley are disassembled or replaced.

Haas Bar Feeder - Installation - NGC - AD0406

Page 13 of 13 pages

Содержание Bar Feeder














Результаты поиска

Содержание Bar Feeder

Отзывы:

Похожие инструкции для Bar Feeder

Бренды по названию

Популярные бренды

Haas Bar Feeder, Руководство по установке

Результаты поиска

Содержание Bar Feeder

Отзывы:

Похожие инструкции для Bar Feeder

Бренды по названию

Популярные бренды