Haas Automation VF Series, Книга управления

Страница: 113 / 127

106
January 2004
POSIT
D Quick Zero on DIST-TO-GO Display - To clear out and get a quick zero position display, for a distance
reference move, use the DIST-TO-GO position display. When you’re in the POSIT display and in HANDLE JOG
mode, press any other operation mode (EDIT, MEM, MDI, etc.) and then go back to HANDLE JOG. This will zero
out all axes on the DIST-TO-GO display and begin showing the distance moved.
D To Origin the POS-OPER Display - This display is used for reference only. Each axis can be zeroed out
independently, to then show its position relative to where you selected to zero that axis. To zero out a specific
axis, PAGE UP or P AGE DOWN in the POSIT display to the POS-OPER large-digit display page. When you
Handle Jog the X, Y or Z axis and then press ORIGIN , the axis that is selected will be zeroed. Or, you can
press an X , Y or Z letter key and then ORIGIN to zero that axis display. You can also press the X , Y or Z key
and enter a number (X2.125), then press ORIGIN to enter the number in that axis display.
D Jog Keys - The JOG keys (+X, -X, +Y, -Y, +Z, -Z, +A, -A, +B, -B) use the jog speeds of 100., 10., 1. and .1
inches per minute listed next to the HANDLE JOG key (jogging with the handwheel uses the .1, .01, .001 and
.0001 inch increments). You can also adjust feed rate using the FEED RATE OVERRIDE buttons, which allow
you to increase or decrease feed rate in 10% increments, up to 200% or using the HANDLE CONTROL FEED
RATE or HANDLE CONTROL SPINDLE keys to adjust the programmed feed or speed 1% up or down with
every increment of the Handle.
D Jog Keys - You can also select an axis for jogging by entering the axis letter on the input line and then pressing
the HANDLE JOG button. This works for the X, Y, Z, and A axes as well as the B, C, U, and V auxiliary axes.
OFSET
D Entering Offsets - Pressing WRITE/ENTER will add the number in the input buffer to the cursor-selected
offset value. Pressing F1 will replace the selected offset with the number in the input buffer.
D Entering Offsets - Pressing OFSET again will toggle back and forth between the Tool Length Offsets and
Work Zero Offsets pages.
D Entering Offsets - In the OFSET display, F1 will set the entered value into the offsets. F2 will set the
negative of the entered value into the offsets.
D Coolant Spigot Position - The coolant spigot can be programmed to move to the location entered in the
OFSET display, on the Tool Geometry Offset page under CLNT POS. You can adjust the coolant nozzle up to
10 different positions for a tool. Position 1 is the farthest up and 10 is the farthest down. The nozzle will shift to
that position whenever an M08 or Hnn code is executed in the program. When you cursor onto the CLNT POS
column, the coolant nozzle location is displayed in the lower left corner.
D Clearing All Offsets and Macro Variables - When you’re in the Tool Length Offset display, you can clear
all the offsets by pressing the ORIGIN key. The control will prompt: “ZERO ALL (Y/N)?” to make sure this is
what you really want to do. If Y is entered, all the offsets in the area being displayed will be zeroed. The Work
Zero Offset page and the Macro Variables page in the CURNT COMDS display will do the same thing.
(Any Mill Control ver. 10.02 and above; any Lathe Control ver. 3.00 and above.)
D The Mill Offers up to 200 Tool Offsets - Mills now offer up to 200 tool offsets. In all previous versions, the
maximum number available was 100 tool offsets.
(Any Mill Control ver. 10.22 and above.)
D Send and Receive Offsets to/from Disk or RS-232 (See the Control Tips Communications section) .