Haag-Streit VISUTRON 900 Touch Скачать руководство пользователя страница 24

Страница: 24 / 88

Instrument Setup

(continued)

Figure IS-32, Near Vision Rod

and Card Holder

Figure IS-33, Card Illuminated

Near Vision Rod and Card

The Visutron 900

Touch

includes a Near vision rod, and a near

vision card attached to a card illuminator. Place the three AAA

batteries in the card illuminator.

Slide the card illuminator onto the near vision rod. Loosen

the convergence lever thumb screw, install the rod into the

convergence lever, and tighten the thumb screw. The reading

rod is held up in the stored position by a spring clip.

Use caution when moving the Visutron 900

Touch

head to

make sure the rod is not accidentally lowered. The card

illuminator will automatically turn on when the rod is lowered,

and turn off when the rod is raised. Use the button on the

underside of the NearBright to adjust the illumination level.

The card illuminator will automatically shut off after 15 minutes

when the rod is lowered.

Face Shields

The Visutron 900

Touch

includes two pairs of face shields.

These are attached with magnets to the patients side of the

Phoroptor head.

Turn the Visutron 900

Touch

On and Off

The ON/OFF switch is located on the Central Unit. The entire

system is powered by the Central Unit and turned ON/OFF

from there.

When the Visutron 900

Touch

is turned ON, the Controller

software will bootup and the Phoroptor head will perform

its initialization procedure. This will take approximately one

minute.

To shut down the system, set the ON/OFF switch to OFF.

16243-101 Rev. G

Содержание VISUTRON 900 Touch

























































































Результаты поиска

Содержание VISUTRON 900 Touch

Отзывы:

Бренды по названию

Популярные бренды

Haag-Streit VISUTRON 900 Touch, Руководство пользователя

Результаты поиска

Содержание VISUTRON 900 Touch

Отзывы:

Бренды по названию

Популярные бренды