Guilin Woodpecker Medical Instrument Endo Radar Plus Скачать руководство пользователя страница 3

Страница: 3 / 45

1 Introduction

1.1 Foreword

Guilin Woodpecker Medical Instrument Co., Ltd. is a high-tech

enterprise in researching, developing, and producing dental equipment,

and has a perfect quality assurance system, main products including

ultrasonic sealer, curing light, Endo motor, apex locator and ultrasurgery,

automatic water supply system etc.

1.2 Introduction

Endo Radar Plus is mainly used in Endodontic treatment. It is a

cordless endo motor with root canal measurement capability. It can be

used as a endo motor for preparation and enlargement of root canals, or

device for measuring canal length. It can be used to enlarge the canals

while monitoring the position of the file tip inside the canal.

Features:

a) Use efficient brushless motor, bringing lower noise and longer

service life.

b) Cordless portable endo motor with combined length determination.

c) The built-in high-capacity battery in the base is equipped with a

wireless charging system to ensure long enough battery life.

d) The contra-angle can be rotated for 360°.

Содержание Endo Radar Plus














































Результаты поиска

Содержание Endo Radar Plus

Отзывы:

Похожие инструкции для Endo Radar Plus

Бренды по названию

Популярные бренды

Guilin Woodpecker Medical Instrument Endo Radar Plus, Инструкция по эксплуатации

Результаты поиска

Содержание Endo Radar Plus

Отзывы:

Похожие инструкции для Endo Radar Plus

Бренды по названию

Популярные бренды