Guilin Woodpecker Medical Instrument Endo Radar Plus Скачать руководство пользователя страница 27

Страница: 27 / 45

Problem

Cause

Solution

After the motor

handpiece is

activated, if

the wireless

communication

connection status

indication is
“

”, the

wireless

connection

between the

motor handpiece

and the base

fails.

1. The wireless

connection has failed

2. Handpiece far from

the base.

1.Press the handpiece “ON/

OFF” button more than 5

seconds to power off and

power on again.

2. Place the handpiece near

the base and power on.

The contra-

angle cannot be

calibrated.

The calibration

procedure may have

been interrupted by

increased resistance in

the contra-angle.

If calibration has been

interrupted, calibrate the

motor handpiece again to rule

out the possibility of a motor

fault.

2.Clean and lubricate the

contra-angle.

3.Start the calibration

procedure again.

Motor handpiece

is getting hot.

Run time is too long

with reciprocating

mode

Allow the device to cool

down and start again the

motor handpiece.

Continuous

rotary file blocks

in the root canal

Wrong file setting.

Too much pressure on

the instrument.

Change the rotational

direction by pressing the

REV key. Start the handpiece

and pull out the file carefully.

Reciprocating

file blocks in the

root canal.

Too much pressure on

the instrument.

File not frequently

clened.

Try to remove the file with a

pair of pliers by pulling out

and rotating the file gently

clockwise.

Содержание Endo Radar Plus














































Результаты поиска

Содержание Endo Radar Plus

Отзывы:

Похожие инструкции для Endo Radar Plus

Бренды по названию

Популярные бренды

Guilin Woodpecker Medical Instrument Endo Radar Plus, Инструкция по эксплуатации

Результаты поиска

Содержание Endo Radar Plus

Отзывы:

Похожие инструкции для Endo Radar Plus

Бренды по названию

Популярные бренды