Gude Expert Power Control 8221 Series Скачать руководство пользователя | Manualshive

Страница: 8 / 97

background image

8

Expert Power Control 8221/8226

© 2021 GUDE Systems GmbH

Device Description

5. Status LED
6. Select button
7. Ok button
8. Ethernet connector (RJ45)
9. External sensor connectors (RJ45)
10. RS232 connector

11. Mains supply Bank B (IEC C20, max.16A)
12. 6 x Load outputs Bank B (IEC C13, max. 16A)
13. 6 x Load outputs Bank A (IEC C13, max. 16A)
14. Mains supply Bank A (IEC C20, max.16A)

Start-up the device

·

Connect the two power cords (IEC C19, max. 16A) to the mains supply. The cable
connectors are secured as regards their type against unintentional loosening. They
must be inserted up to the stop, otherwise there is no secure connection. The plug
must not wobble in the socket, or there is no tight connection.

·

Plug the network cable into the Ethernet socket (RJ45).

·

If required, setup a serial connection to the RS232 port.

·

Insert the optional external sensors into the sensor connectors.

·

Connect the consumers with the load outputs (IEC C13, max. 10A).

1.5

Dual-Circuit Characteristics

The

Expert Power Control 8221-1/8226-1

has two different input circuits (Banks A

and B). Therefore the mains supply A ( IEC C20, max. 16 A ) feeds the current to the
load outputs A1 to A6 (IEC C13, max. 10 A), resp. mains supply B feeds the current to
the load outputs B1 to B6 (IEC C13, max. 10 A ) . The electronics of the device works
when one of the two input circuits is supplied .

«
...
6
7
8
9
10
...
»

Содержание Expert Power Control 8221 Series


































































































Отзывы:

Нет отзывов

Похожие инструкции для Expert Power Control 8221 Series

EasySmart DGS-1100-08

Бренд: D-Link Страницы: 44

Бренд: pathway Страницы: 28

Бренд: GE Страницы: 302

Бренд: Daxten Страницы: 2

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Бренд: Jabra Страницы: 4

Бренд: REV Ritter Страницы: 15

Бренд: N-Tron Страницы: 158

Бренд: GarrettCom Страницы: 39

SmartSTACK ETHERNET ELS10-27

Бренд: Cabletron Systems Страницы: 126

Instant On 1930 Series

Бренд: Aruba Страницы: 8

Бренд: Cabletron Systems Страницы: 56

Бренд: 3onedata Страницы: 4

tekmarNet 4 User Switch 481

Бренд: Tekmar Страницы: 12

Wormhole Station JUH-320

Бренд: j5 create Страницы: 9

Бренд: Clinton Electronics Страницы: 2

EWS-series EWS2910P-Kit-300

Бренд: EnGenius Страницы: 6

Бренд: EMTEST Страницы: 99

Бренд: Encore Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды