Gude Expert Power Control 8221 Series Скачать руководство пользователя | Manualshive

Страница: 27 / 97

background image

27

Expert Power Control 8221/8226

© 2021 GUDE Systems GmbH

Configuration

Enable watchdog: Enables the watchdog function for this Power Port.

Watchdog type: Here you can choose between the monitoring by ICMP pings or TCP
pings.

·

ICMP Pings: The classic ping (ICMP echo request). It can be used to check the ac-
cessibility of network devices (for example, a server).

·

TCP Pings: With TCP pings, you can check if a TCP port on the target device would
accept a TCP connect. Therefore a non-blocked TCP port should be selected. A
good choice would be port 80 for http or port 25 for SMTP.

TCP port: Enter the TCP port to be monitored. When using ICMP pings this is not
needed.

Hostname: The name or IP address of the monitored network device.

Ping interval: Select the frequency (in seconds) at which the ping packet is sent to
each network device to check its operating status.

Ping retries: After this number of consecutive unanswered ping requests the device is
considered inactive.

Watchdog mode: When Reset port when host down is enabled, the Power Port is
turned off and switched back on after the time set in Reset Duration. In mode Switch
off once when host down the Power Port remains disabled.

At the default setting (Infinite wait for booting host after reset) the watchdog monitors
the connected device. When there is no longer a reply after a set time, the watchdog
performs the specified action, usually a reset of the Power Port. Now the watchdog
waits until the monitored device reports again on the network. This may take several
minutes depending on the boot duration of the device. Only when the device is access-
ible from network again, the watchdog is re-armed. If the option Repeat reset on boot-
ing host after x ping timeout is enabled, this mechanism is bypassed. Now the watch-
dog is re-activated after N Ping intervals (input field ping timeouts).

When enabling the IP master-slave mode, the port is switched depending on the avail-
ability of a remote device. Depending on the configuration, the port is switched on
when the terminal is reachable, or vice versa.

«
...
25
26
27
28
29
...
»

Содержание Expert Power Control 8221 Series


































































































Отзывы:

Нет отзывов

Похожие инструкции для Expert Power Control 8221 Series

Бренд: ABLE Страницы: 5

SUPERSTACK 3 3226

Бренд: 3Com Страницы: 5

Бренд: 3Com Страницы: 139

CoreBuilder 7000

Бренд: 3Com Страницы: 150

CoreBuilder 7000

Бренд: 3Com Страницы: 264

Бренд: 3Com Страницы: 574

Бренд: 3Com Страницы: 333

SUPERSTACK 3 3226

Бренд: 3Com Страницы: 70

OfficeConnect 3C16790C

Бренд: 3Com Страницы: 18

Бренд: 3Com Страницы: 1314

SuperStack II Switch 1100

Бренд: 3Com Страницы: 62

Бренд: Kramer Страницы: 2

Бренд: Little Giant Страницы: 2

Бренд: Aastra Страницы: 52

Бренд: Key Digital Страницы: 20

Бренд: Quidway Страницы: 43

Бренд: T.I.P. Страницы: 42

Бренд: Blue Sea Systems Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды