manualshive.com logo in svg

Grundfos CU 362, Инструкция по установке и эксплуатации

Поделиться
Скачать
Grundfos CU 362 Скачать руководство пользователя страница 56

4-3-9-1_INTERLOCK_PIT_1_1

12

Interlock, pit 1

Related information

8.3.3 CIM 250/260 (Modbus and SMS via GSM/GPRS)

8.3.4 CIM 270/280 GRM (Grundfos Remote Management)

8.3.14 GPRS settings

The GPRS communication info is entered in this display.
The user must enter the following:
•

APN (Access Point Node)

•

Username

•

Password.

The SIM card, APN address, username and password are
supplied by the telephone company.

Path:

 Settings > Communication settings > GPRS settings

4-3-10_GPRS_SETTINGS_109

GPRS settings

See the Functional profile and user manual "Grundfos CIM 250,
GSM for Grundfos Dedicated Controls" on the CD-ROM supplied
with the GSM module.

Related information

8.3.3 CIM 250/260 (Modbus and SMS via GSM/GPRS)

8.3.4 CIM 270/280 GRM (Grundfos Remote Management)

8.4 I/O settings

The display shows the options in this menu.

Path:

 Settings > I/O settings

TM078714

I/O settings

Related information

8. The "Settings" menu

8.4.1 Analog inputs

The analog input to be set is selected in this display.
As standard, there are five analog inputs. The display shows each
input so that its physical location can be quickly identified.

Example

The AI1 analog input on the CU 362 (designated terminal 51) is
linked to the function "Level, pressure".
AI1 (CU 362) [51] and AI1 (IO351B-41) [57].

Input

Control unit/
module

Terminal

AI1

CU 362

51

AI1

IO 351B

57

Path:

 Settings > I/O settings > Analog inputs

TM078715

Analog inputs

Analog input, configuration

The analog input to be set is selected in this display.
Each analog input has its own display. The number of displays
depends on the number of analog inputs.

Example

1. Select input signal type, for example, 4-20 mA.
2. Select input value, for example, "Level, pressure".
3. Set sensor measuring range (minimum and maximum limits), for

example, 0.0 to 5.0 m.

If an analog input is disabled, the display only shows the
upper part, that is the input setting.

If the input is enabled, "Measured input value" is shown. A function
can be linked to an analog input in another display. CU
362 returns to the analog input setting display.

56

English (GB)

Содержание CU 362













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды