background image

OM-CBE-10G       7

It is essential to supply the steam generator with water that will not form scale. Even 

though the boilerless steam generator is engineered to minimize scale formation, scale 

development  depends  on  the  hardness  of  your  water  and  the  number  of  hours  you 

operate the equipment each day.

Most water supplies contain minerals which form scale. It is this scale which could lead 

to an early component failure.

Your local water utility can tell you about the minerals in your water. The water going 

to the steam generator should have between 30 and 40 parts per million (ppm) total 

dissolved solids (TDS) and should have a pH (acidity rating) of 7.0 to 9.0. 

Please follow these simple precautions:

1. 

The best way to prevent scale is to use a Groen PureSteam™ Water Treatment 

System which has been specifically designed for Groen steamers and combination 

ovens. 

Do not rely on unproven water treatments

 sold for scale prevention and 

removal. 

They are not specifically designed to work with Groen steamers 

and combination ovens.

2. 

A well-maintained water treatment system and a regular cartridge replacement 

schedule is essential.

3.  

Using a Groen water treatment system will provide longer steam generator/boiler 

life, higher steam capacity, and reduce maintenance requirements.

4.  

If you notice a slowdown in steam production, check the unit’s bottom for scale 

build-up. This could be an indication that the water treatment cartridges need 

replacing. Heavy scale reduces the unit’s ability to boil water, and can even cause 

component failure.

MINIMIZE  SCALE  PROBLEMS  BY  INSTALLING  AND  MAINTAINING  A  GROEN 

WATER TREATMENT SYSTEM AND BY DELIMING THE STEAM GENERATOR/BOILER 

REGULARLY.

Groen  Combination  Ovens  features  two  separate  water  inlets  —  one  for  the  steam 

generator (for treated water), the other for the spray condenser (untreated water) and 

semi automatic wash cycle. The second intake will reduce water treatment requirements 

resulting in significant savings.

The dual water connections are on the rear of the unit.

CAUTION

A FILTER SUITABLE FOR REMOVING FERRITE 
COMPOUNDS IS RECOMMENDED WHEN THE 
WATER SUPPLY HAS HIGHER THAN 50 PPM 
OF IRON CONTENT.  FAILURE TO DO SO COULD 
CAUSE RUSTING OF THE OVEN CAVITY.

Water Quality and Treatment

Standard water connections for steam 

generator and drain spray condenser.

Содержание (2) CBE-10G

























Отзывы: