background image

OM-CBE-10G       21

Deliming

 The oven may be delimed at any temperature.  However, since it is necessary 

to remove the steam lid from the inside of the cavity the oven should be allowed to cool 

before starting the procedure. It is recommended that the oven delime cycle is complete 

before cleaning.

1.  First turn off whatever cooking mode is currently on by pushing its button.

2.  If the oven is off turn it on with the power switch. Push LIGHT. While the LIGHT is 

on push CLEAN. The message OPEN DOOR AND REMOVE STEAM LID appears in 

the display. This indicates that the oven is in deliming mode. If the message OPEN 

DOOR AND REMOVE RACKS appears it means that the LIGHT was not on while 

CLEAN was pushed. You have another chance to put the oven in delime mode. 

Push LIGHT again.  While the LIGHT is on push CLEAN. The STEAM LID message 

should appear.

3.  Open the door and remove the steam lid from the bottom of the cavity. The display 

message changes to ADD DELIMER AND CLOSE DOOR.

4.  Water begins to fill the three reservoirs and the heaters turn on. Pour 1/3 cup of 

delimer into each reservoir, one cup total. Close the door.

5.  The message changes to DELIME MODE TIME LEFT. The oven will steam for 20 

minutes and drain (display message is DELIME MODE DRAIN TIME).

6.  At this time the oven is hot and the display message changes to OPEN DOOR TO 

COOL OVEN.

7.  When the door is opened the display message changes to COOLING.

8.  When the oven has cooled sufficiently to allow it to continue the display message 

CLOSE THE DOOR is displayed.

9.  When the door is closed the oven enters the cleaning cycle at the first rinse step. 

It rinses twice, displays CLEAN COMPLETE TIME LEFT, and turns itself off.

Once a deliming cycle has been started all other cooking modes are inactive (locked 

out). The  deliming  cycle  must  run  to  completion  before  the  oven  will  operate  in  the 

cooking modes.

The oven may be turned off at any time during the deliming cycle. When the oven is turned 
on again it remembers that it was interrupted in the middle of the deliming cycle. The display 
message is PUSH CLEAN TO FINISH CLEANING. The oven enters the clean cycle at the rinse 
step to remove all delimer from the reservoirs and it shuts itself off. It can then be turned on 
and operated in any mode.

Cleaning

WARNING

WHEN HANDLING CLEANER OR DETERGENT 
ALWAYS  WEAR  SUITABLE  GLOVES  AND 
PROTECTIVE  SAFETY  GLASSES.    FAILURE 
TO  DO  SO  CAN  CAUSE  SERIOUS  BURNS.  
TAKE  PRECAUTIONS  TO  KEEP  CHEMICALS 
FROM  CONTACTING  YOUR  SKIN.    KEEP 
THE  CHEMICAL(S)  AWAY  FROM  THE 
DOOR  GASKET  AND  THE  FRONT  CONTROL 
PANEL  GASKET.    FAILURE  TO  DO  SO  CAN 
DRASTICALLY REDUCE GASKET LIFE.

WARNING

AFTER  EACH  CLEAN  CYCLE  CHECK  THE 
INTERIOR  TO  MAKE  CERTAIN  THAT  ALL 
CLEANING RESIDUE HAS BEEN RINSED OFF 
BEFORE  INSTALLING  RACKS  OR  RESUMING 
COOKING.

Содержание (2) CBE-10G

























Отзывы: