Grizzly G0845P Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 68

background image

Model G0845P (Mfd. Since 01/18)

-43-

4. With assistant at rear of machine to support

blade, remove hex nuts and flat washers
loosened in

Step 3, then have assistant pull

blade off frame (see

Figure 63).

5. Installation is reverse of removal.

IMPORTANT: Align keyed flat head cap
screws with slots in blade before tightening
fasteners. Check blade gap after installing
blade (see

Page 38).

Note: Clean mounting surface and blade with
mineral spirits before re-installing blade.

If  the  gibs  are  too  loose,  the  quality  of  the  cuts
will  suffer  because  the  movement  will  be  sloppy
when  the  shear  is  engaged.  If  the  gibs  are  too
tight,  it  will  be  difficult  to  lower  the  upper  blade,
and the cutting edges of the blades may become
damaged.

The goal of adjusting the gibs is to keep the front-
to-back movement of the upper blade frame snug
without interfering with the sliding action.

Items Needed

Qty

Open-End Wrench 19mm .................................. 1
Hex Wrench 6mm .............................................. 1

To adjust gibs:

1. DISCONNECT MACHINE FROM POWER!

2. Loosen (6) hex nuts on gib adjustment set

screws (see

Figure 64).

3. Tighten all (6) gib adjustment set screws

evenly until gibs are snug against copper slid-
ing plates, then back off gib adjustment set
screws

1

⁄

8

turn.

4. Make test cut to check sliding action and

quality  of  cut.  If  necessary,  turn  gib  adjust-
ment  set  screws  clockwise  to  tighten  gib  or
counterclockwise  to  loosen  gib,  then  repeat
test  and  adjust  as  necessary  until  you  are
satisfied with gib adjustment.

5. Hold set screw in position and tighten hex nut

to secure gib adjustment.

Adjusting Gibs

There are four copper plates on each side of the
upper blade frame that ride between the blade
guide and upper blade frame—two front, two rear
(see

Figure 64). They are made of copper so the

plates wear instead of the frame. The rear cop-
per plates act as gibs that apply pressure to keep
movement of the upper blade tight and precise
within the blade guide.

Figure 64. Gib adjustment controls (right side).

Gib

Adjustment

Set Screws

OFF

ON

Blade

Guide

Upper Blade Frame

Rear

Copper

Plate

«
...
43
44
45
46
47
...
»

Содержание G0845P





































































Отзывы:

Нет отзывов

Похожие инструкции для G0845P

Бренд: Nakayama Страницы: 36

Бренд: ABIKOR BINZEL Страницы: 56

Бренд: Panduit Страницы: 16

Бренд: Panduit Страницы: 2

NEWMAR Sentinel

Бренд: Mission Critical Страницы: 28

NittaBeltPoly PI-30

Бренд: Nitta Страницы: 16

Бренд: Prince Castle Страницы: 4

GE-CS 18 Li-Solo

Бренд: EINHELL Страницы: 44

Бренд: Tripp Lite Страницы: 3

Бренд: BGS technic Страницы: 4

Бренд: Malibu Boats Страницы: 2

Бренд: Altronix Страницы: 2

Бренд: Hamamatsu Photonics Страницы: 35

Бренд: National Instruments Страницы: 11

Бренд: Bioenno Power Страницы: 16

Бренд: Widearea Страницы: 9

Бренд: DeWalt Страницы: 6

Бренд: Altronix Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды