Grizzly G0845P Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 68

background image

Model G0845P (Mfd. Since 01/18)

-41-

Reversing &

Replacing Blades

Each blade has two cutting edges so that if one
cutting edge becomes dull, you can reverse the
blade and use the fresh, sharp cutting edge. Each
flat head cap screw is keyed to align with mount-
ing slots in the blades.

If both cutting edges are dull, re-sharpen the
blades on a surface grinder and make sure they
stay flat along their entire length. If the blade
becomes too thin and the cap screw heads extend
beyond the cutting edge, you will need to replace
it. If the blade is nicked or damaged, replace it.

IMPORTANT: ALWAYS check the blade gap after
installation if you reverse, sharpen, or replace the
blades (see

Adjusting Blade Gap on Page 38).

Contact Grizzly at (800) 523-4777 or online at
grizzly.com to purchase Part No. P0845P034. We
recommend you keep an extra set of blades on
hand to minimize downtime.

3. Remove two pressure-regulating hex bolts

on hold-down clamp (see

Figure 60), then lift

out shaft and disc spring stack on each side.

IMPORTANT: DO NOT remove any disc
springs from shaft. Store the disc spring stack
in a safe location until re-installing the blade.

Items Needed

Qty

Hex Wrench 10mm ............................................ 1
Hex Wrench 4mm .............................................. 1
Wrench or Socket 36mm ................................... 1
Socket 25mm and 12" Extension .................1 Ea
Eye Bolts M10-1.5 .............................................. 2
Lifting Strap or Chain (Rated for 500 lbs.) ......... 1
Forklift ................................................................ 1
Mineral Spirits .................................... As Needed
Shop Rags ......................................... As Needed
Another Person .................................................. 1
1x4 and 2x4 Wood Blocks ............................1 Ea
Heavy Leather Gloves .............1 Pair Per Person

Reversing & Replacing Upper Blade

Figure 59. Upper blade cover and finger guard

removal.

Upper

Blade

Cover

Finger Guard

4. Install (2) M10-1.5 eye bolts into top of hold-

down clamp where shown in

Figure 60.

OFF

ON

1. DISCONNECT MACHINE FROM POWER!

2. Remove upper blade cover and finger guard

(see

Figure 59).

IMPORTANT: Note how the finger guard
engages blade guard limit switch. The shear
will not operate if the finger guard is removed
or does not engage the limit switch.

Figure 60. Hold-down clamp removal.

Eye Bolt Holes

Pressure-Regulating

Hex Bolts

The shear blades or hold-

down can easily pinch,

crush, or amputate fingers

or other body parts. Always

keep hands, fingers, and

other body parts away from

the blades and hold-down

during operation.

5. Attach lifting strap or chain to eye bolts, then

lift hold-down clamp with forklift while assis-
tant guides it evenly out of blade guide slots.

«
...
41
42
43
44
45
...
»

Содержание G0845P





































































Отзывы:

Нет отзывов

Похожие инструкции для G0845P

Бренд: Jet Страницы: 2

Бренд: Akyga Страницы: 4

Бренд: HIKOKI Страницы: 16

Бренд: OMERA Страницы: 50

Бренд: Wido Страницы: 16

Бренд: FEAS Страницы: 4

Бренд: F.F. Group Страницы: 32

NetSure 722NBBB

Бренд: Vertiv Страницы: 60

Бренд: Parkside Страницы: 43

Бренд: Sealey Страницы: 3

Бренд: Omer Страницы: 2

Nanogun Airmix H2O

Бренд: SAMES KREMLIN Страницы: 67

Бренд: Fein Страницы: 35

Бренд: Pattfield Ergo Tools Страницы: 92

Бренд: Greencut Страницы: 40

Бренд: Central Machinery Страницы: 16

Бренд: coocazoo Страницы: 18

Бренд: EINHELL Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды