Grizzly G0845P Скачать руководство пользователя страница 46

Страница: 46 / 68

-44-

Model G0845P (Mfd. Since 01/18)

The Model G0845P left and right work stops are
adjusted at the factory to be square, but they can
be adjusted if cutting operations are no longer
producing satisfactory results.

Items Needed

Qty

Hex Wrench 6mm .............................................. 1
Wrench or Socket 18mm ................................... 1
Magnetic Base Blocks (See

Page 31) ............... 2

Carpenter's Square 16" x 24" ............................ 1

Squaring Side Work

Stops

Squaring Left Work Stop

1. Place upper blade at top dead center using

foot switch.

2. DISCONNECT MACHINE FROM POWER!

3. Place (2) magnetic base blocks 12" apart on

right side of lower blade (see

Figure 65).

Squaring Right Work Stop

1. Place upper blade at top dead center using

foot switch.

2. DISCONNECT MACHINE FROM POWER!

3. Place (2) magnetic base blocks 12" apart on

left side of lower blade (see

Figure 65).

4. Place carpenter's square against magnetic

base blocks and left work stop.

5. If square aligns with base blocks and left

work stop, no adjustment is necessary.

6. If left work stop does not align with square,

loosen (2) cap screws securing work stop
to table and adjust work stop to align with
square. Tighten cap screws.

Figure 65. Magnetic base blocks used to check

squareness of work stops.

Lower

Blade

Magnetic

Base Blocks

OFF

4. Place carpenter's square against magnetic

base blocks and right work stop.

5. If square aligns with base blocks and right

work stop, no adjustment is necessary.

6. If right work stop does not align with square,

loosen (2) hex bolts securing work stop
to table and adjust work stop to align with
square. Tighten hex bolts.

Содержание G0845P





































































Результаты поиска

Содержание G0845P

Отзывы:

Похожие инструкции для G0845P

Бренды по названию

Популярные бренды

Grizzly G0845P, Руководство пользователя

Результаты поиска

Содержание G0845P

Отзывы:

Похожие инструкции для G0845P

Бренды по названию

Популярные бренды