Grizzly G0845P Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 68

background image

-22-

Model G0845P (Mfd. Since 01/18)

Figure 21. Connecting power to machine.

Move the disconnect switch handle to the ON
position, as illustrated below. The machine is now
connected to the power source.

Connecting to Power Source

Figure 22. Disconnecting power from machine.

Move the disconnect switch handle to the OFF
position, as illustrated below. The machine is now
disconnected from the power source.

Note: Lock the switch in the OFF position to
restrict others from starting the machine.

Disconnecting from Power Source

4. Make sure wires have enough slack so they

are not pulled tight or stretched.

5. Close and secure electrical box door, then

perform

Test Run.

Test Run

Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning correctly.

If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The

Troubleshooting table in the

SERVICE section of this manual can help.

DO NOT start machine until all preceding

setup instructions have been performed.

Operating an improperly set up machine

may result in malfunction or unexpect-

ed results that can lead to serious injury,

death, or machine/property damage.

Serious injury or death can result from

using this machine BEFORE understanding

its controls and related safety information.

DO NOT operate, or allow others to operate,

machine until the information is understood.

The test run consists of the following: 1) the motor
powers up and runs correctly, 2) the phase polar-
ity is correct, 3) the shear blades have adequate
clearance, and 4) the safety feature works cor-
rectly on both EMERGENCY STOP buttons.

To test run shear:

1. Clear all setup tools away from machine.

«
...
22
23
24
25
26
...
»

Содержание G0845P





































































Отзывы:

Нет отзывов

Похожие инструкции для G0845P

Бренд: Laser Страницы: 2

Бренд: FarmTek Страницы: 7

Бренд: Lambda Страницы: 56

Бренд: Lakeshore Страницы: 122

Бренд: Palmgren Страницы: 20

Бренд: Valcom Страницы: 2

Бренд: Valcom Страницы: 5

Бренд: Valcom Страницы: 5

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Facom Страницы: 56

Бренд: Franke Страницы: 89

Бренд: Wacker Neuson Страницы: 30

ALIENTECH Powergate 3

Бренд: TMC Страницы: 2

Бренд: M-system Страницы: 3

Бренд: DUCTMATE Страницы: 12

Бренд: Trotec Страницы: 10

Бренд: Malibu Boats Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды