Grizzly G0845P Скачать руководство пользователя страница 25

Страница: 25 / 68

Model G0845P (Mfd. Since 01/18)

-23-

2. Press EMERGENCY STOP buttons on con-

trol panel and foot pedestal (see

Figure 23).

4. Connect machine to power (see Page 22).

3. Set both blade gap adjusters at 0.010" as

indicated on each dial (see

Figure 24).

Figure 23. EMERGENCY STOP button

locations.

Foot

Pedestal

Control

Panel

Figure 25. Resetting EMERGENCY STOP

button.

5. Twist each EMERGENCY STOP button

clockwise until it springs out (see

Figure 25).

This resets switches so machine can start.

Figure 24. Location of blade gap adjuster (right).

Blade Gap

Adjuster Dial

6. Turn ON/OFF switch ON. Power indicator

should illuminate (see

Figure 26).

Figure 26. ON/OFF switch, shear switch, jog

button, and power indicator.

Shear

Switch

Jog

Button

ON/OFF

Switch

Power

Indicator

Note: Both EMERGENCY STOP buttons
must be reset before shear motor will run.

EMERGENCY
STOP Buttons

7. Turn shear switch left, then press and hold

jog button (see

Figure 26). Motor should

engage shear and operate smoothly with-
out vibration or excessive noise as long as
button is held in. Release jog button to stop
machine.

Foot Pedal

Содержание G0845P





































































Результаты поиска

Содержание G0845P

Отзывы:

Похожие инструкции для G0845P

Бренды по названию

Популярные бренды

Grizzly G0845P, Руководство пользователя

Результаты поиска

Содержание G0845P

Отзывы:

Похожие инструкции для G0845P

Бренды по названию

Популярные бренды