Grizzly G0636X Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 68

Grizzly G0636X Скачать руководство пользователя страница 3

Table of Contents

INTRODUCTION ............................................... 2

Contact Info.................................................... 2
Manual Accuracy ........................................... 2
Machine Data Sheet ...................................... 3
Identification ................................................... 5
Controls & Components ................................. 6

SECTION 1: SAFETY ....................................... 7

Safety Instructions for Machinery .................. 7
Additional Safety for Bandsaws ..................... 9

SECTION 2: POWER SUPPLY ...................... 10

SECTION 3: SETUP ....................................... 12

Needed for Setup ......................................... 12
Unpacking .................................................... 12
Hardware Recognition Chart ....................... 13
Inventory ...................................................... 14
Cleanup ........................................................ 15
Site Considerations ...................................... 16
Moving & Placing Base Unit ........................ 17
Mounting to Shop Floor ............................... 18
Guide Post Handwheel ................................ 18
Blade Tracking ............................................. 19
Positive Stop ................................................ 20
Dust Collection ............................................. 21
Installing Fence ............................................ 22
Test Run ...................................................... 23
Tensioning Blade ......................................... 24
Adjusting Blade Guide Bearings .................. 24
Adjusting Support Bearings ......................... 26
Aligning Table .............................................. 28
Aligning Fence ............................................. 29
Calibrating Miter Gauge ............................... 29
Calibrating Pointer ....................................... 30

SECTION 4: OPERATIONS ........................... 31

Operation Overview ..................................... 31
Workpiece Inspection................................... 32
Foot Brake ................................................... 33
Table Tilt ...................................................... 33
Guide Post ................................................... 34
Fine Tune Tracking ...................................... 34
Blade Lead ................................................... 35
Ripping ......................................................... 36
Crosscutting ................................................. 36
Resawing ..................................................... 37
Cutting Curves ............................................. 37
Stacked Cuts................................................ 38
Blade Information ......................................... 38
Changing Blade ........................................... 40

SECTION 5: ACCESSORIES ......................... 41

SECTION 6: MAINTENANCE ......................... 43

Schedule ...................................................... 43
Cleaning & Protecting .................................. 43
Brushes ........................................................ 43
Lubrication ................................................... 43

SECTION 7: SERVICE ................................... 46

Troubleshooting ........................................... 46
Checking and Tensioning V-Belts................ 48
Replacing V-Belts ........................................ 49
Adjusting Tension Lever .............................. 49
Adjusting Wheel and Blade Brushes ........... 50
Aligning Wheels ........................................... 50
Adjusting Guide Post Travel ........................ 53

SECTION 8: WIRING ...................................... 55

Wiring Safety Instructions ............................ 55
Electrical Components ................................. 56
Wiring Diagram ............................................ 57

SECTION 9: PARTS ....................................... 58

Main ............................................................. 58
Fence/Guides/Trunnion ............................... 61
Labels & Cosmetics ..................................... 64

WARRANTY AND RETURNS ........................ 65

«
1
2
3
4
5
...
»

Содержание G0636X





































































Отзывы:

Нет отзывов