Grizzly G0636X Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 68

Grizzly G0636X Скачать руководство пользователя страница 20

-18-

Model G0636X (Mfd. Since 09/18)

Although  not  required,  we  recommend  that  you
mount  your  new  machine  to  the  floor.  Because
this  is  an  optional  step  and  floor  materials  may
vary,  floor  mounting  hardware  is  not  included.
However,  you  must  level  your  machine  with  a
precision level.

You may also mount your machine to a mobile
base (see

Figure 10) that has wheel locking or

wheel retracting capabilities that keep the mobile
base from rolling when the bandsaw is in use.
We recommend using the Grizzly Model D2058A
mobile base.

Bolting to Concrete Floors

Lag shield anchors with lag bolts (

Figure 9) and

anchor studs are two popular methods for anchor-
ing an object to a concrete floor. We suggest
you research the many options and methods for
mounting your machine and choose the best that
fits your specific application.

Mounting to

Shop Floor

Figure 9. Typical fasteners for mounting to

concrete floors.

Figure 10. Bandsaw mounted on D2058A mobile

base.

Guide Post

Handwheel

To install guide post handwheel:

1. Insert guide post handwheel onto shaft, and

secure it with cap screw on flat side of shaft,
as shown in

Figure 11.

Figure 11. Guide post handwheel installed.

Anchor studs are stronger and more per-

manent alternatives to lag shield anchors;

however, they will stick out of the floor,

which may cause a tripping hazard if you

decide to move your machine.

«
...
18
19
20
21
22
...
»

Содержание G0636X





































































Отзывы:

Нет отзывов