Grizzly G0636X Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 68

Grizzly G0636X Скачать руководство пользователя страница 47

Model G0636X (Mfd. Since 09/18)

-45-

1. DISCONNECT MACHINE FROM POWER!

2. With table perpendicular to blade, wipe off

all existing grease and sawdust buildup from
rack.

3. Move table up to its maximum 45˚ angle and

wipe (see

Figure 56) off all existing grease

and sawdust buildup from rack.

5. Move table up and down several times to

distribute grease, then wipe off any excess
grease.

4. Apply a thin coat of light all-purpose grease to

rack.

Figure 56. Table tilt rack and pinion assembly.

1. DISCONNECT MACHINE FROM POWER!

2. Move table up until it reaches its maximum

45˚ angle and wipe off all excess grease and
sawdust from trunnions.

3. Apply a thin coat of light all-purpose grease to

trunnions (see

Figure 57).

Figure 57. Trunnion lubrication location.

4. Move table down and then back up to distrib-

ute grease, then wipe off any excess grease
from trunnions.

Table Tilt Rack & Pinion Assembly

Trunnions

«
...
45
46
47
48
49
...
»

Содержание G0636X





































































Отзывы:

Нет отзывов