manualshive.com logo in svg

Grizzly G0636X, Руководство пользователя, Страница: 31 / 68

Поделиться
Скачать
Grizzly G0636X Скачать руководство пользователя страница 31

Model G0636X (Mfd. Since 09/18)

-29-

Aligning Fence

NOTICE

Adjusting the fence parallel to the miter slot 

does not guarantee straight cuts. The miter 

slot may need to be adjusted parallel to the 

side of the blade. Refer to the "Aligning 

Table" instructions on Page 28. 

5.  Tighten knobs and cap screw that secure rail 

to table, being careful not to move fence. 

Figure 33. Example of fence square with miter 

slot.

To ensure cutting accuracy when the fence is first 
installed,  the  fence  should  be  aligned  with  the 
miter slot.

To align fence parallel with miter slot:

1.  DISCONNECT MACHINE FROM POWER!

2.  Make sure miter slot is aligned with bandsaw 

blade (see 

Page 28).

3.  Mount  fence  next  to  miter  slot,  then  loosen 

knobs and cap screw that secure fence rail to 
table.

4.  Adjust fence face parallel with edge of miter 

slot, as shown in 

Figure 33.

The  miter  gauge  needs  to  be  calibrated  to  the 
blade when it is first mounted in the miter slot.

To calibrate miter gauge:

1.  Place  one  edge  of  a  machinist's  square 

against  face  of  the  miter  gauge  and  other 
against blade face, as shown in 

Figure 34.

Calibrating 

Miter Gauge

Angle Pointer 

Screw

Lock 

Knob

Figure 34. Example of squaring miter gauge to 

blade.

2.  Loosen lock knob on miter gauge and adjust 

gauge flush with edge of square.

3.  Tighten lock knob, and verify setting. 

 

Note:  Sometimes tightening procedure can 
affect adjustment.

4.  Loosen screw that secures angle pointer and 

adjust pointer to 0˚ mark on scale.

5.  Retighten screw that secures angle pointer.

Содержание G0636X





































































Отзывы:

Нет отзывов