manualshive.com logo in svg

Grizzly G0636X, Руководство пользователя, Страница: 35 / 68

Поделиться
Скачать
Grizzly G0636X Скачать руководство пользователя страница 35

Model G0636X (Mfd. Since 09/18)

-33-

The Model G0636X is equipped with a foot brake 
(see 

Figure 37). Use the brake only in emergency 

situations to stop power from going to the motor 
and bring the blade to a halt.

Figure 37. Foot brake location.

Foot Brake

Personal injury or death 

can occur if the bandsaw 

starts during table 

adjustment. Disconnect 

power from the bandsaw 

before performing table 

adjustments. 

The bandsaw table will tilt 5˚ left and 45˚ right to 
provide a wide range of cutting options.

To tilt table:

1.  DISCONNECT MACHINE FROM POWER!

2.  Loosen  table  tilt  lock  lever  shown  in  Figure 

38.

3.  To tilt table to the right, turn table tilt handwheel 

clockwise (see 

Figure 38).

Table Tilt

4.  To tilt table to the left, turn table tilt handwheel 

clockwise  one  turn,  lower  positive  stop  bolt, 
then turn handwheel counterclockwise.

5.  Secure table tilt lock lever.

6.  Follow  "Positive  Stop"  instructions  on  Page 

20  for  resetting  stop  bolt  and  table  for  hori-
zontal (0º) operations.

Figure 38. Table tilt controls.

Lock Lever

Table Tilt Handwheel

The foot brake will not stop the bandsaw 

wheels and blade instantly. DO NOT become 

over confident and relax your safety aware-

ness because of the foot brake feature.

Содержание G0636X





































































Отзывы:

Нет отзывов