manualshive.com logo in svg

Grizzly G0636X, Руководство пользователя, Страница: 46 / 68

Поделиться
Скачать
Grizzly G0636X Скачать руководство пользователя страница 46

-44-

Model G0636X (Mfd. Since 09/18)

Figure 55. Tension adjustment assembly 

locations (top wheel removed for clarity).

1.  DISCONNECT MACHINE FROM POWER!

2.  Open top wheel cover and look through top of 

wheel. 

3.  Wipe  off  any  existing  grease  and  sawdust 

buildup on blade tension adjustment assem-
bly and tension lever cam.

4.  Apply a thin coat of grease to tension adjust-

ment  assembly  and  tension  lever  cam  (see 

Figure 55).

Blade Guide Rack & Pinion

1.  DISCONNECT MACHINE FROM POWER!

2.  Lower blade guide until it reaches table.

3.  Wipe off existing grease and sawdust buildup 

on rack (see 

Figure 54).

Figure 54. Rack lubrication location.

4.  Apply a thin coat of light all-purpose grease to 

rack.

5.  Move blade guide up and down several times 

and remove any excess grease to help pre-
vent sawdust buildup.

Blade Tracking Knob

1.  DISCONNECT MACHINE FROM POWER!

2.  Unscrew blade tracking knob 5 turns.

3.  Wipe  off  any  existing  grease  and  sawdust 

buildup on threads.

4.  Apply a few dabs of a light all-purpose grease 

to threads.

5.  Re-adjust  tracking  (see  Blade Tracking on 

Page 19).

Tension Adjustment Assembly

Содержание G0636X





































































Отзывы:

Нет отзывов