manualshive.com logo in svg

Grizzly G0636X, Руководство пользователя, Страница: 43 / 68

Поделиться
Скачать
Grizzly G0636X Скачать руководство пользователя страница 43

Model G0636X (Mfd. Since 09/18)

-41-

SECTION 5: ACCESSORIES

ACCESSORIES

Replacement Blades
These  replacement  blades  are  milled  for  exact 
tooth set and are made with high quality tool steel.

160" Carbon Steel Replacement Blades for the 

Model G0636X.

MODEL

WIDTH

TPI

H8416

3

⁄

16

"

4 SKIP

H8417

3

⁄

16

"

10 RAKER

H8418

3

⁄

16

"

14 RAKER

H8419

1

⁄

4

"

4 HOOK

H8420

1

⁄

4

"

6 HOOK

H8429

1

⁄

2

"

4 HOOK

H8476

1"

6 HOOK

160" Timber Wolf

® 

Replacement Blades for the 

Model G0636X.

MODEL

WIDTH

TPI

T20201

1

⁄

4

"

4  POS. CLAW

T20202

1

⁄

4

"

6 POS. CLAW

T20208

3

⁄

8

"

6 POS. CLAW

T20209

3

⁄

8

"

10 RAKER

T20211

1

⁄

2

 "

3 POS. CLAW

T20212

1

⁄

2

 "

4 POS. CLAW

T20214

1

⁄

2

 "

10 RAKER

T20215

1

⁄

2

"

18 RAKER

162" Carbon Steel Replacement Blades for the 

Model G0636X.

MODEL

WIDTH

TPI

H4819

3

⁄

8

"

6 HOOK

H4820

3

⁄

8

"

10 RAKER

H4821

1

⁄

2

"

4 HOOK

H4822

1

⁄

2

"

6 HOOK

H4823

3

⁄

4

"

3 HOOK

H4824

1"

6 HOOK

H4825

1"

2 HOOK

162" Timber Wolf

® 

Replacement Blades for the 

Model G0636X.

MODEL

WIDTH

TPI

H9567

1

⁄

2

"

3  POS. CLAW

H9568

1

⁄

2

"

4 POS. CLAW

H9569

1

⁄

2

"

6 POS. CLAW

H9570

1

⁄

2

"

10 RAKER

H9571

 1"

3 POS. CLAW

H9572

1"

4 POS. CLAW

H9573

1"

10 RAKER

H9574

1

1

⁄

4

"

3

⁄

4

" PITCH

Some aftermarket accessories  can be 

installed on this machine that  could  cause 

it to function improperly, increasing the risk 

of serious personal injury. To minimize this 

risk, only install accessories recommended 

for this machine by Grizzly.

NOTICE

Refer to the newest copy of the Grizzly 

Catalog for other accessories available for 

this machine. 

order online at

 

www.grizzly.com

 

or call

 

1-800-523-4777

Figure 49. D2058A Shop Fox Mobile Base.

D2058A—Heavy-Duty Shop Fox Mobile Base
This  patented  base  is  the  most  stable  on  the 
market with outrigger type supports. Adjusts from 
18

1

⁄

2

" x 24

1

⁄

2

" to 28

1

⁄

2

" x 33

1

⁄

2

". 1300 lb. capacity. 

Weighs 39 lbs.

Содержание G0636X





































































Отзывы:

Нет отзывов